SAS Anchors

A compact, economical shingle-roof anchor that blends in and installs fast. The D-Minus uses a 7/8" connector hole instead of a D-ring and mounts with six fasteners into wood framing. Choose gray powder-coated 11-ga steel or 11-ga 430 stainless to match your environment. For retrofit installs over existing shingles, pair it with the RetroFlash flashing to cover the anchor and fasteners for a clean, weather-protected finish. Features Low-profile, shingle-roof design — specified for asphalt...

The D-Minus anchor is our most economical fall arrest anchor and is available in gray powder coated 11-gauge mild steel or 11-gauge 430 stainless steel. Installs with 6 factory supplied stainless steel spiral shank nails or an optional #12 screws. This anchor is specified for use on asphalt shingle roofing and is low profile making them difficult to notice on the roof. This anchor can be used for new construction, reroof or retrofitting onto existing roofs. In addition, this anchor can be used...

The RS-20 anchor is a permanent roof anchor designed specifically for tile, slate, wood and synthetic roofing materials. The 20” long strap allows you to adjust the reveal of the D-ring for your specific roofing material and the unique design of the anchor also allows you to physically bend the D-ring portion of the anchor up and over the tile or slate so that it lays flat on the surface. This permanent, low profile anchor comes with stainless steel attachment hardware and comprehensive...

The Safety Bar is a temporary, reusable open-framing anchor that gives crews a safe tie-off point before sheathing or full bracing. It spans three trusses, locks in with stainless detent pins, and automatically gauges trusses at 24" on center. Rated for two users and compatible with shock-absorbing lanyards or SRLs, it’s a fast, rugged solution for truss-stage fall protection. Features Made for 2×4 top chords: Model 1010 sized for 2×4 trusses; bars for other sizes available separately. ...

The Moveable ARS 2x8 is a permanent, flashed roof anchor designed to mount to 2x8 top chords and stay in place for the life of the roof. It provides a low-profile tie-off point you can position to suit the shingle layout, then seal in with the included flashing kit for a clean, watertight finish. Built for single-person fall arrest or restraint with a 5,000 lb rating, it uses heavy-duty hardware for a rigid, durable connection and a molded stem cover to keep water out and the installation...

A reusable, hinged roof anchor for fast, reliable tie-off on wood-framed roofs. The 3006 mounts at the ridge or in the field and accepts nails (included) or approved screws. Built from 11-gauge zinc-coated steel and rated to 5,000 lb for single-user fall arrest/restraint, it conforms to steep pitches or lays flat on the deck and meets common OSHA/ANSI requirements. Features 1-person roof anchor for wood framing; install at ridge or field locations. 11-gauge zinc-coated steel construction for...

#1 selling anchor for reroof, new construction and remodeling. The low-profile design is aesthetically pleasing and is designed to last the life of the structure. The Retro-Fit is designed to give all who access the roof a reliable tie-off point. Installs with just 8 nails and comes with special butyl waterproof flashing strips to seal the stainless-steel nails. Fabricated with 430 stainless steel and certified for over 5,000 pounds. Use over asphalt shingle, wood shake or metal roofing, the...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

The Combo Safety Bar is a temporary, reusable open-framing anchor designed to protect crews during the truss-setting phase—before sheathing is installed. It spans three trusses, auto-gauges spacing at 24 inches on center, and locks on with stainless detent pins. The dual-size saddle design fits both 2x4 and 2x6 top chords, so one bar covers multiple framing packages. Rated for two users when used with appropriate PFAS components, the bar provides a rugged, highly visible tie-off point that...

The RS-10 is a compact, stainless steel retrofit anchor designed for fast, watertight installs on new or existing shingle roofs. At 8-1/2" long, it sits over the roofing material and provides a low-profile, single D-ring tie-off for routine access, service work, and permanent protection. Rated to 5,000 lb and compliant with OSHA/ANSI, it’s a rugged, one-person anchorage you can trust at the ridge, hip-ridge, or in the field. Features Built for shingles & retrofits: 8-1/2" length allows...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

The Super Anchor 2833 and 2833-DP TrussBar anchors are temporary moveable anchors designed for use during framing and sheathing. They fit 2x4 and 2x6 top chords spaced 24 inches on center and support up to two users for fall arrest or restraint. After roof sheathing is complete, the anchor remains in place but becomes nonfunctional while tie-off straps are removed or cut off. Features Temporary framing-stage roof anchor Supports two users for fall arrest or fall restraint Fits 2x4 and 2x6 top...

A rugged, versatile anchor for single-user fall protection that you can mount in a variety of ways depending on the structure. The D-ShakL2 uses a heavy-duty shackle with a captured, free-rotating D-ring to simplify clipping in and reduce twist at the connection point. Install temporarily to wood framing with WS screws, or make it permanent by bolting or welding to steel or by using engineered concrete anchors. Rated to 5,000 lb and built with a hot-dip galvanized finish for long service life,...

Purpose-built for tile and slate roofs, the 2815T is a permanent, low-profile double D-ring anchor that slides under the last course so only the rings show. Its extended strap (with ~40" between D-rings) lets you hit structure while keeping a clean look, and it installs without penetrating the sheathing. A factory butyl strip and stainless fasteners help deliver a water-resistant, long-lasting tie-off point that meets OSHA/ANSI. Features Tile/slate ready: Designed for high- and low-profile...

A permanent roof anchor engineered for pre-engineered metal buildings that use Z-purlins. The Super Z-Purlin Anchor provides a discreet, code-compliant tie-off point for routine access and service work. The single pack includes everything needed for a watertight install—anchor, stem, EPDM flashing with vulcanized aluminum strip, Grade 8 bolts, and the installation manual—so crews can achieve a clean, reliable finish in one visit. Rated to 5,000 lb for one user, it’s built from...

Built for metal building purlin structures, this permanent Z-purlin anchor provides secure, single-user connection for both fall arrest and fall restraint. The 11-gauge 430 stainless steel body resists corrosion, while an EPDM flashing base with a vulcanized aluminum strip helps seal out weather. Rated to 5,000 lb minimum breaking and tensile strength, it’s a rugged, long-term solution for rooftop safety on industrial and commercial sites. Features Dual-mode safety: Supports fall arrest and...

A compact, jobsite-tough anchor strap designed to create a quick tie-off around beams, posts, or truss chords. One end features a slotted D-ring that lets the strap cinch cleanly and stay put; the opposite end uses a small D-ring for your connector. The 36-inch length is easy to route in tight spaces, and the heavy-duty webbing stands up to daily use while staying flexible for fast installs. Features 36 in overall length for tight or confined anchorage points Heavy-duty, abrasion- and...

The Swivel-D anchor is a fully articulating anchor that rotates 360-degrees and swivels 180-degrees. It can attach to virtually any structure including steel, wood, and concrete. It is manufactured with a heavy-duty stainless-steel shackle and a zinc-plated 2.0” inside diameter forged steel D-ring. It is a highly durable anchor that can be used for either temporary or permanent installation on the interior or exterior of your building or structure. This anchor is very universal in its...

The Safety Bar 1011 is a temporary, reusable open-framing anchor built specifically for 2x6 top chords. It spans three trusses, locks in place with stainless detent pins, and gives crews a safe, stable tie-off point during the hardest stage to protect—before roof sheathing is installed. Rated for two users and rugged enough for everyday jobsite use, it sets spacing, speeds production, and helps maintain compliant fall protection from the moment trusses go up. Features Purpose-built for 2x6...

A tough, 72-inch webbing anchor strap that creates a fast, reliable tie-off point around beams, trusses, columns, or other approved structures. One end features a forged D-ring for easy clipping; the other end is a reinforced loop that cinches cleanly without bulky hardware. Built for everyday jobsite abuse, it integrates into standard PFAS setups for a single user and stows compactly when the task is done. Features 72 in length provides generous wrap/anchorage options on wood, steel, or...

The CRA D-Plate is a permanent, low-profile roof anchor that mounts over structure and disappears under the finished roof for a clean look. A heavy-duty steel plate with a centered D-ring provides a dependable single-user tie-off point for routine access, maintenance, and construction tasks. Designed for wood-framed roofs and flashed into the roofing system, it delivers a 5,000 lb rated anchorage that meets common jobsite standards while keeping the installation discreet. Features Low-profile...

A permanent rooftop tie-back anchor designed for façade access, window washing, and suspended maintenance systems. The 1301-G uses a compact D-plate with a heavy-duty connection ring to provide a dependable, single-user tie-back point while keeping a low profile on the roof. Built for attachment to structural steel or concrete and finished for long service life, it supports proof-load testing and labeling practices commonly required for Cal-OSHA-regulated buildings. When installed to an...

A rugged, 72-inch anchor strap that creates a quick, reliable tie-off around beams, posts, and truss chords. The slotted D-ring end lets you choke the strap tight so it stays put; the opposite end provides a compact D-ring connection point for your lanyard or SRL. Built from heavy-duty 2-inch polyester webbing with forged steel hardware, it’s tough enough for daily use yet flexible for fast installs and easy stowage. Features 72 in overall length and 2 in webbing width for versatile wraps...

The SAS-2801 ARS 2×8 is a permanent stainless steel roof anchor designed for residential fall protection applications. It installs to 2×4, 2×6, or 2×8 rafters and can be drill-through mounted on 2×10 or 2×12 members. Each anchor includes a TPE flashing and stem cover to integrate with asphalt shingle or wood shake roofing while maintaining a watertight seal. Features Permanent fall protection roof anchor Stainless steel construction, 5,000 lb minimum strength Supports 2×4, 2×6, 2×8 rafters;...

The Hinge-2 (No. 3013-D) is a tough, reusable roof anchor built for fast setup on wood-framed structures. Its hinged legs conform from flat deck to steep pitches, while a forged D-ring provides a dependable tie-off for a single user. Rated to 5,000 lb and compliant with OSHA/ANSI, it installs with SAS-specified nails or screws and can be used at the ridge or in the field—even vertically on a wall with the proper screws. Features Reusable, 1-person anchor for fall arrest or restraint; max user...

The WS-TrussBar™ is an SAS exclusive design specified for use in attic spaces where other types of fall protection anchorage devices are not practical to install. Manufactured from lightweight aluminum, the WS-TrussBar™ easily installs to the underside of all standard size top chords and is adjustable for 12”, 16” and 24” top chord spacing. The bar legs easily rotate to compensate for imperfect top chord spacing. Use for single person PPE tie-off or HLL systems. This anchor can be used as a...

A ready-to-install wall-mount anchorage that creates a dependable tie-off point on vertical wood, steel, or concrete structure. The 1004A kit pairs a heavy-gauge steel anchor plate with a forged connection ring and matched fasteners, so crews can bolt up quickly and get a single-user, 5,000-lb rated attachment for maintenance, access, or construction tasks. Compact, corrosion-resistant, and inspection-friendly, it’s designed to live on the wall where you need routine protection without...

A purpose-built anchorage solution for vertical framing. The 1004 kit creates a dependable tie-off point on stud walls, posts, or headers so crews can work safely on decks, scaffolds, and wall lines during framing and finish phases. The steel anchor plate and forged connection point combine with the included fasteners to deliver a rugged, job-tough installation for a single user when mounted into solid structure. Use with an energy-absorbing lanyard or SRL and follow the service-zone and...

The Super Anchor EPDM Metal Roof Flashing base was specifically designed to flash the ARS Series of anchors on standing seam and corrugated metal roofing. The Flashing system consists of a medium gray EPDM Base Flashing with aluminum reinforced edge, a gray stem cover and a tether strap. Flashing size is 8”x8” with a 3” stem height. The flashing has ribs on the bottom to accept butyl type sealant. Fasteners are not included to attach the flashing to the roof. The flashing conforms easily to...

The Super Anchor 1032-W, 1033-W, and 1042-W CRA-W posts are permanent loop-top anchor points intended for tie-off and window washing systems. They provide certified anchorage with a minimum breaking strength of 5,000 lb and loop tops rated up to 10,000 lb. Each model differs by riser height (12", 18", 24") to suit different roof and application requirements. Features Loop top anchor posts designed for single user PPE tie-off Minimum breaking strength: 5,000 lb Loop top tensile rating: up to...

The D-ShakL2 1029-S is a rugged, stainless single-user anchor that installs almost anywhere you have sound structure. A 316 SS shackle with a captured 304 SS forged D-ring delivers a smooth, free-rotating tie-off, while the design supports multiple attachment methods—temporary wood installs with WS screws or permanent bolt/weld/concrete attachments—so you can standardize on one anchor for diverse jobs. Rated 5,000 lb and compliant with ANSI Z359.18-17 Type D and OSHA 1926.502, it’s a...

A temporary, reusable anchorage designed specifically for open-framing work over 2x4 floor joists. The 1017A spans across joist bays and locks in with quick-release detent pins—no nails or screws into the joists—so crews get a safe, stable tie-off point before the subfloor goes down. Rugged steel construction, a low-profile center tie-off, and jobsite-friendly handling make it a dependable solution for interior framing and deck-edge tasks. Features Purpose-built for 2x4 floor joists; installs...

The Form-It is a temporary use roof anchor that can be installed onto a flat surface or a pitched roof. Anchor legs are pre-bent to 25-degrees. Easy to adjust the anchor by hand to match the roof pitch. Installs with 10 of the 16d vinyl sinkers through the sheathing and into a top chord. Maximum exposure time is 6 months from install date. Evacuate by removing or flattening the anchor stem over. Features: Fall Arrest Rated for 5,000 pounds14 gauge zinc plated steelAttached with 10 ea. 16d...

The Super Anchor Evac™ series (1062, 1063, 1064) is a temporary, one-person roof tie-off anchor that fastens to top chords during framing and is removed (evacuated) from the roof after completion. These anchors are designed to install to rafters (2×4, 2×6, or 2×8 depending on model), support fall arrest and fall restraint at a 5,000 lb minimum breaking strength, and then be driven flush into the attic when their service is done. Including a bolt kit and tether strap in the package, the Evac...

A tough, temporary reusable anchor that conforms to steep or flat roofs. The Flex Chain Anchor uses heavy-duty zinc-plated steel legs and a flexible 6 mm rubber hinge with a link-chain and 3″ connector ring for fast, reliable tie-off on wood-framed structures. Rated 5,000 lb and supplied with both nails and WS screws, it’s built for quick installs, everyday durability, and compatibility with SAS engineered HLL kits. Features Temporary & reusable: Installs on wood framing; remove and relocate...

The Super Anchor ARS 2×4 anchors are permanent stainless steel roof anchors designed for residential structures. Models 2830, 1022, and 1030 each provide a secure tie-off point for one user and integrate with roofing systems using included TPE flashing and stem covers. Built to a 5,000 lb minimum breaking strength, these anchors are OSHA and ANSI compliant and designed for long-term service life. Features Permanent stainless steel roof anchors for 2×4 framing Minimum tensile strength 5,000 lb...

The CRA-4 4-Way anchor line allows multiple horizontal lifeline segments to intersect on a single anchor point. Models 1032-4G, 1033-4G, 1042-4G offer riser heights of 12", 18", and 24" respectively, with foam-filled risers and a cast loop top. Each unit is rated for a 5,000 lb minimum base tensile strength and is engineered to support intersection of up to four HLL directions. Key Features Multi-direction horizontal lifeline intersection anchor (4-Way) Foam-filled riser for durability and...

The 1044-WG and 1045-WG are hot-dip galvanized steel loop-top risers designed to be field welded to structure, providing a permanent anchor point for single-user fall protection. The 1044-WG has a 12-inch riser height, while the 1045-WG is 18-inch, both with 3.0-inch outer diameter risers. Each riser meets minimum base tensile strength of 5,000 lb and loop-top tensile rating of 10,000 lb, and is suitable for window washing, PPE tie-off, and horizontal lifeline use. Features Weld-on loop-top...