Fall Protection Anchors

FallTech Rotating Deck Anchor is designed for maximum versatility and safety with a 360° self-orienting D-ring for use in temporary Fall Arrest or Restraint applications. The reusable Rotating Deck Anchor is designed for installation onto exposed #10 rebar and threaded rod and is secured with user-supplied rebar wing nut or hex nut. Designed for installation onto 1" diameter exposed threaded rod or exposed #10 rebar.Features: For use in Fall Arrest and Fall Restraint applications. Features...

Roof Top Anchor for Modified Bitumen Membrane and Built-up roofs, with weathering proofing shroud

Roof Top Anchor for PVC Membrane and Built-up roofs, with weather proofing shroud

Roof Top Anchor for Standard membrane and Built-up roofs, with Weather Proofing Shroud

Designed for Installation to flat or low sloped Aluminum, Steel or Stainless Steel standing seams roofs. This anchor can be fitted to a range of sheet materials and seam profiles including bulb and folded types.No need to attach to a structural member! Available toggle bolt kits (6" & 12") allow you to mount anchor on top of insulation.

Designed for Installation to flat or low sloped Aluminum, Steel or Stainless Steel standing seams roofs. This anchor can be fitted to a range of sheet materials and seam profiles including bulb and folded types

Heavy-duty 1 3/4" polyester webbing with rugged forged alloy-steel hardware.3" wear pad protects primary webbing from cuts and abrasion.Ideal for I-beams and other properly rated structural members.Economical and lightweight.Can be used repeatedly.Meets the requirements of OSHA 1926 and ANSI Z359

Heavy-duty 1 3/4" polyester webbing with rugged forged alloy-steel hardware.3" wear pad protects primary webbing from cuts and abrasion.Ideal for I-beams and other properly rated structural members.Economical and lightweight.Can be used repeatedly.Meets the requirements of OSHA 1926 and ANSI Z359

Heavy-duty 1 3/4" polyester webbing with rugged forged alloy-steel hardware.3" wear pad protects primary webbing from cuts and abrasion.Ideal for I-beams and other properly rated structural members.Economical and lightweight.Can be used repeatedly.Meets the requirements of OSHA 1926 and ANSI Z359

FallTech's Ringed Plate Anchor provides a temporary safety solution for workers performing work on building exteriors and roofs. Installed over a truss on the field of wood frame structures, the Ringed Plate Anchor serves as a single user point for personal fall arrest and restraint systems. The fallTech Ringed Plate Anchor is ideal for use during tasks such as painting, siding, roofing, window cleaning, or general constructionFeatures:Temporary fall protection for residential and light...

The Guardian Minotaur Anchor is a dual adjusting anchor for steel beams that is designed to fit beams from 12 in. all the way up to 30 in. wide and 2-1/2 in. thick. The Minotaur Anchor is no tools necessary, easy to use, lightweight, strong and Meets all applicable OSHA and ANSI standardsFeatures:High Strength Load BarAdjustment Clamps and TogglesAdjustable D-Ring w/ 180 degree SwivelLightweightSuperior StrengthMeets all applicable OSHA and ANSI standardsMinotaur Anchor Instructions ...

The Guardian Vertical Beamer 3000 is suitable for installation onto either Vertical or Horizontal I-beams compatible with beams of a wide variety of flange widths and thickness, this Vertical Beamer installs at a fixed position on the beam and is suitable for the connection of either a connecting device or a horizontal lifeline. The Vertical Beamer 3000 can easily be installed by one person without the need for any tools or special equipment, and its durable components allow it to stand up...

The Guardian Fall Protection Hold Me Rope Anchor, functions to integrate an anchorage connector with a vertical lifeline system. The anchor is certified to withstand loads up to 5,000 pounds. Its made from light weight and corrosion resistant aluminum. To use, install rope through the anchor and either connect it with a compatible carabiner to a separate anchorage connector, or loop around a compatible anchor point and pull through the anchor, and create a self-contained system. Its quick and...

The Guardian Fall Protection Anchor connector functions to safely install an Anchorage Connector from ground level. Used in combination with a VLS or SRL (Sold Separately) The user connects their VLA or SRL to the system aluminum hook anchorage connector, then uses the system telescopic pole to raise the aluminum hook anchorage connector up to a compatible structural anchor point. The user then connects their full body harness to the VLA or SRL, and can climb up to the work surface while fully...

The Guardian Screw-Down Metal Roof Anchor is a temporary and reusable anchor point, designed to be used with SRL's up to 50ft. in length. This anchor easily installs on Flat wood or Metal substrates, and allows for the attached SRL to rotate a full 360 degrees. Made from power-coated steel for increased durability. Features:Can be used with most retractable lifelines up to 50ft. (or up to 65ft. in length if used in a combination with the retractable swivel adapter) Allows the...

The 1″ Removable Concrete Anchor 10K is designed for use in 10 inch thick, cured concrete with a compression strength of at least 3000 p.s.i. It is suitable for fall arrest, fall restraint, and as a work positioning device.● Meets ANSI Z359.1-2007, ANSI A10.32-12 and CE-EN 795● Compliant with OSHA 1926.502 and OSHA 1910.66● Size: 1″● Weight: 0.9-lbs● Used in concrete substrate only● Breaking Strength: 10,000 lbf / 44kn● Applications include: fall protection, restraint, work positioning ...

The 3/4″ Removable Concrete Anchor 5K (Part # A6002) is designed for use in 12 inch thick cured concrete with a compression strength of at least 3000 p.s.i. It is easy to install (just compress its spring and insert the cable shaft into the hole). This multifunctional anchor may be used on vertical and overhead surfaces, as well as in combination with horizontal lifelines. It is suitable for fall arrest, restraint, and as a work positioning device. It has a maximum capacity of 400 pounds when...

The 7/8″ Precast Concrete Toggle Lok Anchor 5K is a versatile, portable precast concrete/steel anchorage connector, used exclusively for fall protection. It’s easy to install (just compress its spring and insert the cable shaft into the hole and can be inserted inside precast concrete and steel flanges. Designed for use in 12 inch thick cured precast concrete with a compression strength of at least 3000 p.s.i.● Meets ANSI Z359.1-2007, ANSI A10.32-12 and CE-EN 795● Compliant with OSHA 1926.502...

The 3/4″ Precast Concrete Toggle Lok Anchor 5K is a versatile, portable precast concrete/steel anchorage connector, used exclusively for fall protection. It’s easy to install (just compress its spring and insert the cable shaft into the hole) and can be inserted inside precast concrete and steel flanges. Designed for use in 12 inch thick cured precast concrete with a compression strength of at least 3000 p.s.i.● Meets ANSI Z359.1-2007, ANSI A10.32-12 and CE-EN 795● Compliant with OSHA 1926.502...

The I-Beam Trolley Anchor (Part # A6101) is a Fall Arrest anchor designed to be used in combination with either a shock absorbing lanyard or an SRL. It may also be used for fall restraint and as a work positioning device. Its free moving rollers allow for smooth travel around the work area while always remaining connected. e safety locking toggles allow for easy adjustment and also eliminate the risk of accidental clamp slippage. For use by one worker with a combined weight of up to 310...

The Beam Walker Super Slider 3″ – 12″ is a fall arrest anchor designed for use on the top flange of a steel I or H beam. Light, smooth, and easy to use, the Beam Walker Super Slider 3″ – 12″ is designed for fall protection, rope access and work positioning. ● Meets ANSI Z359.1-2007, ANSI A10.32-12 and CE-EN 795● Compliant with OSHA 1926.502 and OSHA 1910.66● Range: 3″ to 12″● Breaking Strength: 5,000 lbf / 22kn● Weight: 3.4-lbs / 1.58 kg

The Beam Walker Super Slider 3″ – 14″ is a fall arrest anchor designed for use on the top flange of a steel I or H beam. Lighter, smoother, and easy to use, the Beam Walker Super Slider 3″ – 14″ is designed for fall protection, rope access and work positioning.● Meets ANSI Z359.1-2007, ANSI A10.32-12 and CE-EN 795● Compliant with OSHA 1926.502 and OSHA 1910.66● Beam Flange Width Range: 3.5″ to 14″● Beam Flange Thickness: .25″ to 1.25″● Breaking Strength: 5,000 lbf / 22kn● Product Weight: 3.3...

The Beam Walker Super Slider 12″ – 30″ is a large version (30” capacity) fall arrest anchor designed for use on the top flange of a steel I or H beam. Light, smooth, and easy to use, the Beam Walker Super Slider 12″ – 30″ is designed for fall protection, rope access and work positioning.● Meets ANSI Z359.1-2007, ANSI A10.32-12 and CE-EN 795● Compliant with OSHA 1926.502 and OSHA 1910.66● Beam Flange Width Range: 12″ to 30″● Beam Flange Thickness: .25″ to 2.5″● Breaking Strength: 5,000 lbf /...

The 5K Wire Rope Sling – 6ft is an ANSI Z359 certified anchorage connector with iridescent blue tubing for easier cable inspections. Sling can be used in a basket configuration. Cable slings are excellent temporary and semi-permanent ANSI certified anchors. They are available in 3 and 6 foot lengths with various terminations for versatility on the job or in a rescue kit.● Meets ANSI Z359.1-2007 and ANSI A10.32-12● Compliant with OSHA 1926.502 and OSHA 1910.66● Product Weight: 1.3 lbs.●...

The PitchPro is a premier fall protection anchor designed for sloped-roof asphalt shingle construction. The PitchPro is the perfect solution for both new and existing construction, and its low-profile installation makes it an excellent choice for permanent applications. Its oversized connection point makes attaching and detaching easy and bind-free. Made from robust powder-coated steel, the PitchPro resists damage from repeated installations, and ensures the longest possible lifespan. Feat...

The PitchPro is a premier fall protection anchor designed for sloped-roof asphalt shingle construction. The PitchPro is the perfect solution for both new and existing construction, and its low-profile installation makes it an excellent choice for permanent applications. Its oversized connection point makes attaching and detaching easy and bind-free. Made from robust powder-coated steel, the PitchPro resists damage from repeated installations, and ensures the longest possible lifespan....

The PitchPro is a premier fall protection anchor designed for sloped-roof asphalt shingle construction. The PitchPro is the perfect solution for both new and existing construction, and its low-profile installation makes it an excellent choice for permanent applications. Its oversized connection point makes attaching and detaching easy and bind-free. Made from robust powder-coated steel, the PitchPro resists damage from repeated installations, and ensures the longest possible lifespan....

The SSRA2 Roof Jack Adapters are part of the Standing Seam Roof Anchor system. They allow you to mount 2 in. x 10 in. walk-boards to over 500 standing seam roof panels. The SSRA2 adapter plate simply mounts on top of a Standing Seam Roof Anchor (SSRA1, available separately) that has had the D-ring removed. Constructed of solid 6061-T6 aluminum with stainless steel hardware. The adjustable height stabilizer legs provide a steady mounting bracket on hundreds of different seams.*Brackets should...

The SSRA3 Universal Mounting Plate was engineered as a secure non-penetrating mounting solution for various equipment on standing seam roof systems. Constructed of 6061-T6 Aluminum and professionally tested to over 10,000 lbs., far beyond the strength of any roofing system. The SSRA3 is pre-drilled to accept the FallTech 7395A / 7395D Rotating SRD anchor and self retracting devices up to 65 ft. However, up to 12 additional mounting holes may be drilled to accept a wide range of equipment....

Fall Protection Distributors LLC, brings you a revolutionary product allowing Homeowners, Building Owners, and Contractors to work safely on standing seam roofs without penetrating the panels. The Standing Seam Roof Anchor (SSRA1). The patented, Non-Penetrating design of this devise is unlike anything currently available. Its the only certified component system for mounting just about anything to a standing seam roof. The interchangeable mount allows for attachment of devices from various fall...

Fall Protection Distributors LLC, brings you a revolutionary product allowing Homeowners, Building Owners, and Contractors to work safely on standing seam roofs without penetrating the panels. The Standing Seam Roof Anchor (SSRA1). The patented, Non-Penetrating design of this devise is unlike anything currently available. Its the only certified component system for mounting just about anything to a standing seam roof. The interchangeable mount allows for attachment of devices from various fall...

Each Kit Contains:(1) 20 ft. Horizontal Lifeline kit, factory assembled with (2) hinged roof anchors, 3/8 in. cable, cable sliders, fasteners.Features:Factory Assembled3 users in fall restraint or 2 in fall arrestFasteners can be used up to 20 timesSuper Heavy Duty HLL Kit ...

Each Kit Contains:(1) 20 ft. Horizontal Lifeline kit, factory assembled with (2) hinged roof anchors, 3/8 in. cable, cable sliders, fasteners, and cargo bag.Features:Factory Assembled3 users in fall restraint or 2 in fall arrestFasteners can be used up to 20 timesCargo Carrying BagSuper Heavy Duty HLL Kit ...

The SurfaceTech Premium X-Arm Strap from guardian, will not only keep you safe, but it will always stay clean for maximum performance. Guardian, is now offering Surfacetech webbing on many of its web based products. Surfacetech webbing is molecularly altered to form microscopic peaks and valley in the fiber structure, which functions to greatly reduce the surface area that come in contact with contaminants. Paints, Chemicals, or lunchtime mustard will simply run off the surface, while heavier...

The SurfaceTech Premium X-Arm Strap from guardian, will not only keep you safe, but it will always stay clean for maximum performance. Guardian, is now offering Surfacetech webbing on many of its web based products. Surfacetech webbing is molecularly altered to form microscopic peaks and valley in the fiber structure, which functions to greatly reduce the surface area that come in contact with contaminants. Paints, Chemicals, or lunchtime mustard will simply run off the surface, while heavier...

The RIDGEPRO anchor is the ultimate device to help roofing professionals mount and dismount a ladder on steep-slope roofs. The RIDGEPRO grips the roof peak before the user steps off the ladder. It's pushed to the peak with an extension pole. A lanyard connects the RIDGEPRO to the user's safety vest. This allows the worker to install the anchor, then safely hoist himself onto the roof's surface. With it's durable design and it's maneuverability, the RIDGEPRO may be used repeatedly to ensure a...

Details: Zinc-Plated Steel Anchorage DeviceGalvanized O-Ring: 3.75” Round Galvanized O-Ring Thickness: 0.4” Anchor Size: 2” x 4” x 6” Base Thickness: 3/8” Bolts: 1/2”-13, 2-1/2” Grade 5 with 1/2” Lock Washers Strength Rating: 5,000 lbs Capacity: 130-310 lbs.

● Meets ANSI Z359.1-2007 and ANSI A10.32-12● Compliant with OSHA 1926.502 and OSHA 1910.66● Beam Flange Width Range: 4″ to 14″● Beam Flange Thickness: .25″ to 1.25″● Breaking Strength: 5,000 lbf / 22kN● Product Weight: 7 lbs.

The 2-Foot Concrete Web Anchor Strap with Loop and D-Ring is constructed using heavy-duty 1-inch polyester webbing with a 1-5/8-inch polyester wear tube installed to prevent damage from abrasion. It is an excellent temporary anchor for use in new concrete construction, which can be cut off and discarded when work is completed. The looped end attaches to rebar prior to pouring, and is ready to use after curing. It is ideal for shear walls, columns, etc. and can be used on both vertical and...

FallTech 7440 5,000 lb. 3/4 in. Removable bolt anchor, is a reusable anchor designed to be used in cured existing concrete structures. It can be installed in minutes with simple tools and relocated as needed. Meets OSHA and ANSI requirements 

Single-Use roof anchor with nails features user fold-bend to fit roof peaks. Single-use temporary anchor can be removed or hammered down

The solution for the roofing professional who currently has rope and harness equipment. Includes an 8’ extension pole that extends and locks at 16’, which covers a vast majority of current, residential roofing structures. Has a quick-release button made of fiberglass-reinforced nylon with a heavy duty brass locking pin, a hexagonal inner pole made of anodized aluminum and a threaded tip. (Pole in photograph will be different from pole delivered.) Also includes The RIDGEPRO™ – the ultimate tool...

The new Falltech Chain Roof Anchor, is a highly portable and reusable anchor to be used on residential and commercial wood structures. The Anchors O-Ring serves as the attachment point for either a PFAS or on HLL system. With it's heavy steel anchoring plates and flexible belted rubber center, the Chain Roof Anchor can be installed either on the ridge or on the field of a roof and may be used on flat or pitched surfaces. The Anchor is Easily installed with nails as a Single-Point anchor...

Single Use / Fits any Pitch Convenient and disposable Easy to install by nailing into the truss Fasteners provided Complies with OSHA 1926:502(d)(15) Just hammer over the attachment point when the job is done and reinstall roofing substrate over destroyed anchor point

FallTech 7410 Reusable Roof Anchor is constructed using rugged alloy steel with a yellow chromate finish. It is easily installed and removed from trusses or sheathing and uses either 12 #14 x 3½" screws of 20 16d nails. Fits any roof peak up to 12/12 and can also be mounted perfectly flat. Rated at over 5,000 lbs. Economical because it can be used again and again Holes are clearly marked for use with either nails or screws Screw holes are counter-sunk so screws are flush with the anchor Meets...

Features : Forged D-ring and Bolt-on Plate Provides Simple Overhead Anchorage Solution For use on steel I-beams, columns and other steel structures Heavy-duty steel construction 2" x 4-1/2 plate with 1/2" holes

Features : Forged D-ring Plain/Uncoated Steel Plate for Weld-on or Bolt-on Applications Can be installed wherever weld-on applications are preferred Provides Simple Overhead Anchorage Solution For use on steel I-beams, columns and other steel structures Heavy-duty steel construction 2" x 4-1/2 plate with 1/2" holes

Double D-ring; Permanent Roof Anchor with Stainless Steel Body; Fastens Under Shingles, Leaving D-rings Exposed for Attachment; 17" Including D-rings with 12" Nailing Surface. For permanent placement under ridge cap roofing materials Conforms to roof peaks of 1/12 or greater Stainless steel strap with alloy steel d-rings

Single D-ring, Permanent Roof Anchor with Stainless Steel Body; Fastens Under Shingles, Leaving D-ring Exposed for Attachment; 19" Including D-ring with 17" Nailing Surface. Fastens under roofing materials leaving D-ring exposed for attachment of Personal Fall Arrest System

For use on roofs from flat to 12/12 pitch, wood or metal. 5000 lb. anchor point. Fasteners included. Tested and approved for metal roofing applications, minimum 20 gauge metal or thicker, attached directly onto the surface. For metal installation: use (16) screws (8 per side), 6 in center column of fastener installation holes, in 1 hole left of center and 1 hole right of center. Guardian recommends HILTI Kwik-Pro self-drilling screws.

Permanent roof anchor is shingled-over leaving only the D-ring exposed Provides a fall protection anchor point during initial construction as well as for the future homeowner for general roof maintenance Ideal for new or retrofit construction on roofs with asphalt, shake or tile roofing materials Simply install by nailing through sheathing and truss on roof or peak using the eight 20d sinker nails supplied Stainless steel construction and zinc plated steel D-ring resist corrosion for extended...

Ultimate Protection and Safety Our Knock-Down disposable roof anchor is a simple and safe residential and light commercial construction solution. This anchor can have significant impact on jobsite safety while reducing injuries and costly insurance company claims. The unique design provides workers with a fall protection anchor during initial construction, and can simply be “knocked-down” and shingled over when the job is complete. Simple, Fast & Efficient Installation The roof anchor is...

Wood or Metal Deck Applications 5,000 lb. anchorage point Forged alloy D-ring Painted steel construction Includes 20 16D nails for single use 3 lbs. total weight Instructions * This anchor may be installed on steel decking with a minimum material thickness of 22 gauge (.030 inch) over Z-purlins with a minimum material thickness of 16 gauge (.064 inch). The maximum span between purlins is 6 feet. Twelve 1/4"-14 screws are required to fasten the anchor. The screws should be of sufficient length...

5000 lb. anchor point Variable pitch roofs Fasteners included for Fall Arrest rating Use fasteners only once

FEATURES: Removable/Reusable 1/4" thick steel roof anchor Complete with zinc plated forged alloy steel O-ring Nail or bolt into the roof member) Designed to be removable, it may be used again after an inspection 5,000 lbs. minimum breaking strength Anchor is supplied with all necessary fasteners Used for fall arrest or fall restraint Part of our residential horizontal lifeline system

Beamer 2000 The Guardian Fall Protection Beamer 2000 is a versatile Fall Arrest anchor designed for use both overhead and at foot level. Attachable to both steel I and H beams, the Beamer 2000 offers Nylon bushings to provide smooth movement along the beam, that also function as impact indicators in the event of a fall. This extremely durable anchor also includes a precision machined aluminum bar and ratcheting end pieces, which allow for quick and easy adjustment with just one hand. When used...

Beamer 2000 The Guardian Fall Protection Beamer 2000 is a versatile Fall Arrest anchor designed for use both overhead and at foot level. Attachable to both steel I and H beams, the Beamer 2000 offers Nylon bushings to provide smooth movement along the beam, that also function as impact indicators in the event of a fall. This extremely durable anchor also includes a precision machined aluminum bar and ratcheting end pieces, which allow for quick and easy adjustment with just one hand. When used...

Beamer 3000 The Guardian Fall Protection Beamer 3000, the newest in our line of beam anchors, combines the many versatile features of the Beamer 2000 with some new innovations. The Beamer 3000 weighs 25% less than its predecessor, making it one of the lightest beam anchors available on the market. It also includes a dual adjustment feature that makes it even easier to adjust to its ideal position. No more unsnagging a connector or a lifeline when working at heights, the new and improved Beamer...

The Guardian Fall Protection Bull Ring Anchors are suitable for personal fall arrest, restraint, or work positioning applications. For all applications, the worker weight capacity range (including all clothing, tools, and equipment) is 130 to 310 pounds. The anchor itself is constructed of 100% zinc-plated steel. Substrate must be roof truss or support beam that is minimum of 3" thick CDX or better. All fasteners (use either six 16d, 3" long 8 gauge nails or three 1/4" x 3" zinc-plated steel...

Wood screws for use with the Guardian Skyhook and CB Roof Anchors.

Self-drilling metal screws for use on the Guardian Skyhook and CB Roof Anchors.

Mounts on Top of the Skyhook for Retractables Easy installation Swivels 360 degrees Removable and reusable bolt-on application Cost effective accessory to the skyhook Great for first-worker-up system Does not include skyhook or retractable

Mounts on top of the CB-12 or CB-18 for retractables Easy installation Swivels 360º Removable and reusable bolt application Cost effective accessory to the CB Does not include CB anchor CB-InstructionsCB-Tech Sheet ...

The Guardian Fall Protection 'Adjustable Skyhook' can adjust to fit a flat to 12/12 roof pitch. This anchor point also has a 360° Swivel D-ring for easy attachment. This product is powder-coated for a durable weather proof finish. Can adjust from flat to 12/12 roof pitch Attached 360° Swivel D-ring Powder-Coated

Features: Mounts on top of a roof Includes 3 retractable cradles which rotate 360 degrees Accommodates most retractables up to 65' Schedule 80 pipe provides a super strong center post and is designed to take the load of 3 workers falling at the same time when used as a personal fall arrest system The base plates provide further absorption to the system as they engage three trusses Fasteners included ***Does not include retractables***

This specially designed Skyhook allows for attachment down the center of a truss with screws. This is the stabilizer to the SkyMast.

FEATURES: For permanent use on wood rooftops D-ring on one end Meets standards for fall arrest Permanent application Discreet design Stainless steel anchor Easy installation

FEATURES: For permanent use on wood rooftops D-ring on both ends Meets standards for fall arrest Permanent application Discreet design Stainless steel anchor Easy installation

For Asphalt Shingle, Wood, Copper, Slate, Metal and "Simulated Tile" Metal Roofs Strap Length 13" / Total Length 18" Includes 8 stainless steel spiral nails for permanent installation Many older and recently constructed homes do not have roof anchors – so the Retro-Fit Anchor is the perfect solution. The anchor is designed to be installed by removing only a portion of the ridge and does not require a conventional flashing system. Use over asphalt shingle, wood shake or metal roofing, the butyl...

For Tile Strap Length 353" / Total Length 4018" Includes 8 stainless steel spiral nails for permanent installation Many older and recently constructed homes do not have roof anchors – so the Retro-Fit Anchor is the perfect solution. The anchor is designed to be installed by removing only a portion of the ridge and does not require a conventional flashing system. Use over asphalt shingle, wood shake or metal roofing, the butyl flashing strip attached to the underside of the anchor will provide...

For Asphalt Shingle, Wood, Copper, Slate, Metal and "Simulated Tile" Metal Roofs Total Length 18" Fasteners Included For high and low profile roof tiles that does not require a flashing system. Conforms to the pan or barrel section of the tile. Can be retro-fitted onto an existing roof. Rated for 5000 lbs.

Want another valuable tool that’s more than just a safety device? The Safety Bar not only provides a sturdy tie-off point, but also accurately spaces your top chords 24” o.c. And we built this bar to last! It spans 3 trusses at the same time and can be rolled down the roof as the trusses are placed. Utilize numerous bars to provide multiple tie-off points. The Safety Bar is made from cold rolled steel and powder coated bright red. The top chord sockets are held in place using the same high...

For TileFor high and low profile roof tiles that does not require a flashing system. Conforms to the pan or barrel section of the tile. Can be retro-fitted onto an existing roof. Rated for 5000 lbs.

The Guardian Fall Protection "Truss Boss Anchor" is a non-corrosive anchor designed to be attached to the truss while on the ground in less than a minute. FEATURES: Non-corrosive anchor Installs in less than a minute Instructions Data Sheet ...

FEATURES: Includes anchor, gasket and flashing cap Installs in less than a minute Extremely cost effective Attach Truss Boss Anchor to truss while the truss is on the ground Non-corrosive anchor

The Guardian Fall Protection "T-T Boss Anchor Kit" is used for fall arrest or fall restraint. The product comes with environmental safe aluminum flashing with vulcanized EPDM. The included cap is made of Luran-S which is highly durable and designed not to blow off. No fasteners can penetrate the top sheathing of this product. The included anchor can be put on the truss while the truss is on the ground. The hassle free flashing design makes this product extremely easy to install and allows for...

The Guardian Fall Protection "T-T Boss Anchor Kit" is used for fall arrest or fall restraint. The product comes with environmental safe aluminum flashing with vulcanized EPDM. The included cap is made of Luran-S which is highly durable and designed not to blow off. No fasteners can penetrate the top sheathing of this product. The included anchor can be put on the truss while the truss is on the ground. The hassle free flashing design makes this product extremely easy to install and allows for...

The Guardian Fall Protection "T-T Boss Anchor Kit" is used for fall arrest or fall restraint. The product comes with environmental safe aluminum flashing with vulcanized EPDM. The included cap is made of Luran-S which is highly durable and designed not to blow off. No fasteners can penetrate the top sheathing of this product. The included anchor can be put on the truss while the truss is on the ground. The hassle free flashing design makes this product extremely easy to install and allows for...

Removable D-ring assembly allows you to leave behind the clamp assembly and shingle over it, leaving nothing to stick out from the roof and re-use D-ring assembly. Install by clamping onto joist, rafter, etc. Includes flashing to prevent water leakage through the roof during construction. 5000 lb. minimum breaking strength.

Nothing works better to fill the fall protection gap than our ARS Moveable Anchor. Ideal for times when you don’t have a permanent anchor available, or when performing work with limited duration fall hazards. The ARS Moveable is made from 11 gauge stainless steel and is powder coated red for high visibility. The attachment device is a high quality aircraft grade 3/8" diameter stainless steel detent locking pin with a T-handle. It is durable enough to stand up to the kind of abuse common in the...

Nothing works better to fill the fall protection gap than our ARS Moveable Anchor. Ideal for times when you don’t have a permanent anchor available, or when performing work with limited duration fall hazards. The ARS Moveable is made from 11 gauge stainless steel and is powder coated red for high visibility. The attachment device is a high quality aircraft grade 3/8" diameter stainless steel detent locking pin with a T-handle. It is durable enough to stand up to the kind of abuse common in the...

2 Workers Tied Off at the Same Time For builders who want to provide an anchor for trades but does not want it to stay permanently Use the truss spanner during framing and sheeting stage Feed tie-off straps up through or in-between sheeting All trades post sheeting have a tie-off point Roofer cuts off straps when house is finished

3' Tie-Off / Cut Off Straps Feeds through or in-between sheeting All trades post sheeting have a tie-off point

Siding and related external wall construction, such as window installation and painting, expose workers to an even greater risk than working on elevated surfaces such as the roof. Falls from scaffolding and especially ladders, accounts for more serious injuries than any other job site hazard. Vertical Wall Anchors provide an easy cost effective way to provide protection that can be left in place or removed from service. The low visibility anchor stem comes in two standard configurations...

Siding and related external wall construction, such as window installation and painting, expose workers to an even greater risk than working on elevated surfaces such as the roof. Falls from scaffolding and especially ladders, accounts for more serious injuries than any other job site hazard. Vertical Wall Anchors provide an easy cost effective way to provide protection that can be left in place or removed from service. The low visibility anchor stem comes in two standard configurations...

Want another valuable tool that’s more than just a safety device? The Safety Bar not only provides a sturdy tie-off point, but also accurately spaces your top chords 24” o.c. And we built this bar to last! It spans 3 trusses at the same time and can be rolled down the roof as the trusses are placed. Utilize numerous bars to provide multiple tie-off points. The Safety Bar is made from cold rolled steel and powder coated bright red. The top chord sockets are held in place using the same high...

Want another valuable tool that’s more than just a safety device? The Safety Bar not only provides a sturdy tie-off point, but also accurately spaces your top chords 24” o.c. And we built this bar to last! It spans 3 trusses at the same time and can be rolled down the roof as the trusses are placed. Utilize numerous bars to provide multiple tie-off points. The Safety Bar is made from cold rolled steel and powder coated bright red. The top chord sockets are held in place using the same high...

2" D-Ring Slips Through a 3" D-Ring Wraps around I-beams and other structures forming a secure attachment point for lanyards and other connecting devices

Durable anchorage connectors for many applications. Features include a pass-thru loop end design for easy use. Cross arm straps are convenient end points for use with horizontal lifeline systems.

Durable anchorage connectors for many applications. Features include a pass-thru loop end design for easy use. Cross arm straps are convenient end points for use with horizontal lifeline systems.

The Malta Dynamics RA12 (A6300 – Roof Anchor 12″ Standard) is a fixed post roof top anchor, intended for permanent applications only. The RA12 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 12 inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The RA12 is composed of durable galvanized...

The Malta Dynamics RA18 (A6301 – Roof Anchor 18″ Standard) is a fixed post roof top anchor, intended for permanent applications only. The RA18 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 18 inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The RA18 is composed of durable galvanized...

Malta Dynamics 4’ Cross Arm Strap includes a dual enforced heavy duty wear pad and stitching. The heavy duty wear pad protects the structural webbing against abrasion. Each strap includes both a large D-ring and standard size D-ring for easy pass-thru.Key Features:● Product Weight: 1.5 lbs.● Increased durability with dual enforced webbing and heavy duty stitching● The heavy duty wear pad protects the structural webbing against abrasion and snags● Large D-ring and standard size D-ring for easy...

Malta Dynamics 6’ Cross Arm Strap includes a dual enforced heavy duty wear pad and stitching. The heavy duty wear pad protects the structural webbing against abrasion. Each strap includes both a large D-ring and standard size D-ring for easy pass-thru.Key Features:● Product Weight: 1.5 lbs.● Increased durability with dual enforced webbing and heavy duty stitching● The heavy duty wear pad protects the structural webbing against abrasion and snags● Large D-ring and standard size D-ring for easy...

Durable anchorage connectors for many applications. Features include a pass-thru loop end design for easy use. Cross arm straps are convenient end points for use with horizontal lifeline systems.

The Guardian Fall Protection "Premium Cross Arm Straps" are twice as durable with dual enforced webbing and heavy duty stitching. The heavy duty wear pad protects the structural webbing against abrasion and snags. Each strap features a large D-ring and standard size D-ring for pass-thru, which increases the versatility of length adjustment. To shorten the anchorage connector, simply wrap the webbing around the anchorage and pass through the large D-ring. FEATURES: Twice as durable with dual...

The Guardian Fall Protection "Premium Cross Arm Straps" are twice as durable with dual enforced webbing and heavy duty stitching. The heavy duty wear pad protects the structural webbing against abrasion and snags. Each strap features a large D-ring and standard size D-ring for pass-thru, which increases the versatility of length adjustment. To shorten the anchorage connector, simply wrap the webbing around the anchorage and pass through the large D-ring. FEATURES: Twice as durable with dual...

The Guardian Fall Protection "Premium Cross Arm Straps" are twice as durable with dual enforced webbing and heavy duty stitching. The heavy duty wear pad protects the structural webbing against abrasion and snags. Each strap features a large D-ring and standard size D-ring for pass-thru, which increases the versatility of length adjustment. To shorten the anchorage connector, simply wrap the webbing around the anchorage and pass through the large D-ring. FEATURES: Twice as durable with dual...

The Guardian Fall Protection "Premium Cross Arm Straps" are twice as durable with dual enforced webbing and heavy duty stitching. The heavy duty wear pad protects the structural webbing against abrasion and snags. Each strap features a large D-ring and standard size D-ring for pass-thru, which increases the versatility of length adjustment. To shorten the anchorage connector, simply wrap the webbing around the anchorage and pass through the large D-ring.FEATURES:Twice as durable with dual...