Fall Protection Anchors

Safety Bar Temporary/Reusable Anchor The Safety Bar is a unique fall protection anchor for use while working with open truss situations. It spans 3 trusses and locks in securely with detent pins while gauging the trusses 24” on center. 2 users and tie off to the safety bar with the use of a shock absorbing lanyard or SRL’s. Our Safety Bar is the only product on the market for open framing fall protection and is used by framing crews across the country for OSHA compliance during the absolute...

The SSRA3 Universal Mounting Plate was engineered as a secure non-penetrating mounting solution for various equipment on standing seam roof systems. Constructed of 6061-T6 Aluminum and professionally tested to over 10,000 lbs., far beyond the strength of any roofing system. The SSRA3 is pre-drilled to accept the FallTech 7395A / 7395D Rotating SRD anchor and self retracting devices up to 65 ft. However, up to 12 additional mounting holes may be drilled to accept a wide range of equipment....

The Malta Dynamics Single Use Roof Anchor is a handy addition to the roofer’s toolbox. It can be easily bent over the peak of the roof or manipulated to match the pitch of your roof. Because of its versatility and durability, this adjustable pitch anchor creates a reliable tie-off point for your lifeline without causing lasting damage to the rooftop. When installing on the roof, make sure to locate the roof’s crossbeam so that you are anchoring into a strong and solid surface that can support...

Leading edge retractables (models with an attached shock absorber pack) are designed for use in applications to provide added protection against lifeline wear and/or cutting, when working near leading edges, where a fall may occur. This could include, but is not limited to, roofing or eaves, sheared, cold rolled, or cut steel, and edge work on concrete and various decking operations. USE CAUTION…..and provide additional protection against cutting (i.e. a heavy pad) over the exposed sharp edge....

This 15′ webbing anchor with a ratchet strap, designed for use around columns and posts. The ratchet allows for the anchor to stay in the correct position on the column.FEATURES Ratcheting tensioner, 15′ lengthFor use around booms, columns and posts Attachment Points: D-RingMaterials: 2” Double-locking ratchet buckle, breaking strength > 10,000 lbs 2” Polyester webbing, breaking strength > 5,000 lbs High-strength polyester stitches, breaking strength > 40 lbs Heat-treated alloy steel...

Does your jobsite feature a flat roof surrounded by a parapet wall? If it does, then you need a way to anchor your self-retracting lifelines (SRLs). Malta Dynamic's parapet clamp system allows you to put your SRL in place with a sturdy connection that helps support weight and keep your workers safe. The reusable device is easy to install and won’t cause damage to the wall. Your workers can use our parapet anchor on walls varying in thickness from 2.36″ to 14.1″. On a jobsite, time is critical,...

Designed specifically for the Metal Building industry, our Super Z-Purlin provides an easy to install anchorage device that includes attachment bolts. The stem height of the anchor is compatible with high rib roofing panels and blanket type insulation. Waterproofing is achieved using a high quality E.P.D.M. gray colored flashing boot and matching stem cover that has an aluminum flange allowing it to be configured easily to any shape panel. The anchor stem features a collapsible design that...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

The Guardian Fall Protection Bolt Hole Anchor is a reusable 5,000 pound certified anchorage connector that can be used in either horizontal or vertical applications. Incredibly easy to install, the Bolt Hole Anchor simply needs to be squeezed to release its locking mechanism, inserted into a compatible hole ranging from 3/4" to 1—1/4" in width, and then released to reengage the locking mechanism.Features:  Easy to installCompatible with horizontal lifelinesSqueeze to open, release to lock...

The Guardian Fall Protection CB Anchor Series are perhaps the most proven fall protection anchors on the market. CB Anchors are compatible for installation onto wood and steel (fasteners are included). The anchor post functions to extend though roofing so that it is accessible both during and after roof construction, and is compatible for use with SRLs, vertical lifelines, horizontal lifelines, and shock absorbing lanyards. CB Anchors are composed of durable, galvanized steel, and are an...

The Guardian Fall Protection BMR Anchor is a Fall Arrest anchor designed to be used in combination with either a shock absorbing lanyard or SRL. It may also be used for Restraint and Work Positioning applications. Its free moving rollers allow for smooth travel around the work area while always remaining tied off, and its safety locking toggles allow for both easy adjustment and eliminate the risk of accidental clamp slippage.Easy to installFree moving rollersLightweight and durableClick here...

Having an anchorage point on wheels has been a revolution in fall protection. We know that the industry has long sought a more compact fall protection solution, and thus we are extremely proud to introduce the Safety Bull. Smaller than the original TriRex and lighter than the Stinger the Safety Bull is our most versatile mobile fall protection unit. When the Safety Bull is on the roof, two workers can attach to the anchorage point, put tools on the...

The Swivel-D anchor is a fully articulating anchor that rotates 360-degrees and swivels 180-degrees. It can attach to virtually any structure including steel, wood, and concrete. It is manufactured with a heavy-duty stainless-steel shackle and a zinc-plated 2.0” inside diameter forged steel D-ring. It is a highly durable anchor that can be used for either temporary or permanent installation on the interior or exterior of your building or structure. This anchor is very universal in its...

We have recently upgraded our horizontal lifeline systems to include a 4-person 100' rope, which can be shortened to any length. 2-person capacity on standing seam roofs and 4-person capacity when anchored with cross arm straps. Temporary Horizontal Lifeline Kit Includes 100' Kernmantle Rope, won't scratch metal roof panels. Everything you need to provide a temporary Horizontal Lifeline on a 22 ga. or 24 ga. steel standing seam roof.Kit Includes: Four Standing Seam Roof Anchors (SSRA1)Two...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

SafeWaze Cross arm strap made with reinforced webbing and two individually sized D-rings for easy pass through set up.FEATURES 6′ - 20' length2 Pass-through D-ringsHigh-strength polyester stitching3” Polyester webbing with 1.75 in (44.45 mm) reinforced webbing Attachment Points: 2 Pass-through D-ringsMaterials: 1.75 in (44.45 mm) Polyester webbing w/ 3” reinforced webbing; High-strength polyester stitching; Forged steel D-ringsWeight Capacity/Max Working Load: 310 lbs (140.61 kg)Applicable...

The Guardian Fall Protection CB-1-W Weld-On Anchor is 2.75" in diameter, and may be used in a variety of fall protection applications. It includes a forged steel D-ring and can withstand loads up to 5,000 pounds. This anchor is suitable for installation onto either vertical or horizontal steel structures.Features: Weld on steel applicationTemporary anchor pointPermanent application permissible if user applies appropriate finishForged steel D-ringApplicable Standards: OSHA 1910 & OSHA...

The Skyhook™ Swivel Top is great for the first-worker up system. The swivel top is easy to install as it mounts on top of the Skyhook™ anchor point via its removable and reusable bolt-on application. This product allows for a self-retracting lifeline to swivel a complete 360 degrees. This product does not include a Skyhook™ or retractable lifeline. Features: Easy installationSwivels 360 degreesRemovable and reusable bolt-on applicationCost effective accessory to the skyhookGreat for...

New SteelGrip beam clamp is lightweight, ergonomic and easy-to-useRated at over 5,000 lbs.Dual adjust ratchet helps to self-center worker's acnhorage on flangeMeets the requirements of OSHA 1926 and ANSI Z359Features aluminum crossbar and steel clamping jaws with nylon slider padsFits beam flanges from 3" to 14" wide and up to 1-1/4" thick.Dual adjusting jaws include concealed locking latchesAlloy steel D-ring remains centered on crossbarFor temporary mobile use on horizontal I-beams ...

This removable concrete anchor has an exclusive “Easy Button” feature that is sure to boost productivity by providing immediate anchor removal and instant user mobility. The anchor can be set as hard as desired without fear of it getting stuck.FEATURES 5K rated removable concrete wedge anchor designed for 3/4″ by 3″ holeIncorporates easy trigger for repeated use5,000 lbs max capacity10.75″ overall length / Requires 3/4″ hole drilled for placement Materials: Steel body; Stainless steel cable...

Tie-Off Straps are made from 2” wide polyester or nylon and are designed for use as temporary anchorage points to connect vertical lifelines, SRL’s, web lanyard and rope lanyards. Use on wood, steel and concrete structures. Tie-Off straps are wrapped, cinched around the structure to make for a secure anchor or can be embedded into concrete and evacuated when finished with the job. Please see the part number list below for Application, Length, Compliance and Packaging information for all our...

The Guardian Fall Protection Cable Choker Anchor is an ideal lightweight and portable anchorage connector. To use, cinch around a compatible beam or other structural anchor, attach with a compatible lanyard or SRL, and you are ready to work. Available with a variety of connector and pass-through options. Features:  Easy to installSuperior durabilityResistant to wear and abrasionO-Ring Ends 2 ½” & 3”Length: 6 ft.  Technical Data:  Applicable Standards: ANSI Z359.18-17, ANSI...

The Beam Walker Super Slider 3″ – 14″ is a fall arrest anchor designed for use on the top flange of a steel I or H beam. Lighter, smoother, and easy to use, the Beam Walker Super Slider 3″ – 14″ is designed for fall protection, rope access and work positioning.

These anchors are sheathed in heavy duty nylon webbing to protect their inner core from any abrasion and wear, and are some of the most cost effective anchors around. They can be installed as permanent anchors during building construction to protrude through poured concrete, as well as in temporary applications such as wood framing, rebar work, and pipe racking—though always ensure that the selected attachment point can withstand loads of up to 5,000 pounds. Concrete Anchor Straps are intended...

Malta Dynamics Vertical/Fixed Beam Anchors (Part #A6105) are designed for fall protection, rope access, and work positioning. This beam anchor is constructed with lightweight aircraft aluminum bars and a 360 degree swivel D-Ring connector. The clamps attach without tools to I-Beams either overhead or underfoot. This model has a breaking strength of 5,000 lbs. (22kN). If you need a beam anchor for fall protection, the vertical beam anchor is one of the best on the market.

These anchors are sheathed in heavy duty nylon webbing to protect their inner core from any abrasion and wear, and are some of the most cost effective anchors around. They can be installed as permanent anchors during building construction to protrude through poured concrete, as well as in temporary applications such as wood framing, rebar work, and pipe racking—though always ensure that the selected attachment point can withstand loads of up to 5,000 pounds. Concrete Anchor Straps are intended...

The FrogLink Temporary Roof Anchor is a temporary anchor point with built-in energy absorber and 360° working radius. Ideal for wood roofs. Can be used as a single point anchor or as part of a horizontal lifeline system.FEATURES: Stainless steel construction360° working radiusBuilt-in energy absorber reduces stress & damage to the mounting structureEasily attaches with 7, 14 gauge 75 mm long roofing screws (not included)Single User ...

Investment cast alloy steel jaws with nylon sliders.Lightweight aluminum flange barEasy ratcheting adjustment for quick installation and removal.Fits flange widths from 4" - 12" and up to 1" thick.Rated at over 5,000 lbs.Meets the requirements of OSHA 1926 and ANSI Z359Features aluminum crossbar and steel clamping jaws with nylon slider padsSingle adjusting jaw includes concealed locking latchAlloy steel D-ring slides with jaw adjustmentFor temporary mobile use on horizontal I-beams ...

FallTech 7410M Reusable, Hinged Roof Anchor with heavy duty D-ring is constructed using alloy steel with a yellow chromate finish. Manufactured for attachment to metal decking, its hinged design conforms to most roof peaks and can be mounted perfectly flat Features 10" x 3" anchoring plates with 2-1/4" connecting D-ringHinged design conforms to flat or sloped surfaces up to 12/12 pitch.Includes 2-1/2" sheet metal screws for steel deck and metal roof installationFor temporary reusable...

Part of our CB Anchor Series, the S-Anchor is perhaps one of the most proven fall protection anchors on the market. The S-Anchor is designed for either fall protection or suspension/tie-back work. The S-Anchor functions to extend though roofing so that it is accessible both during and after roof construction, and is composed of durable, galvanized steel. It is an excellent choice for fall protection or window washing applications! Features: Easy to installCompatible with horizontal...

These anchors are sheathed in heavy duty nylon webbing to protect their inner core from any abrasion and wear, and are some of the most cost effective anchors around. They can be installed as permanent anchors during building construction to protrude through poured concrete, as well as in temporary applications such as wood framing, rebar work, and pipe racking—though always ensure that the selected attachment point can withstand loads of up to 5,000 pounds. Concrete Anchor Straps are intended...

The Guardian Fall Protection Beamer 3000, the newest in our line of beam anchors, combines the many versatile features of the Beamer 2000 with some new innovations. The Beamer 3000 weighs 25% less than its predecessor, making it one of the lightest beam anchors available on the market. It also includes a dual adjustment feature that makes it even easier to adjust to its ideal position. No more unsnagging a connector or a lifeline when working at heights, the new and improved Beamer 3000...

The Beam Walker Super Slider 12″ – 30″ is a large version (30” capacity) fall arrest anchor designed for use on the top flange of a steel I or H beam. Light, smooth, and easy to use, the Beam Walker Super Slider 12″ – 30″ is designed for fall protection, rope access and work positioning.

New for 2023: The A5 Concrete Expansion Anchor is a popular 5,000 lb anchorage connector for concrete substrates. Its ergonomic thumb rest makes installation fast, easy, and comfortable to use. The expanded connection loop eases anchor connectivity and includes a clear view cable protection to aid during inspection.

The newest addition to Tie Down's mobile fall protection line, Big Foot offers even easier portability while allowing work on concrete, TPO, and EPDM. This lightweight series provides fall arrest for one person and an additional two in restraint. With a gross weight of 750 lbs., nearly half the weight of the Squatch, Bigfoot includes a jacking feature for easy mobility and handling, printed instructions, and hoist rings for lifting. Available in both a USA model and a Canadian model, this...

Non-penetrating, adjustable anchor for standing seam roofs The Adjustable Standing Seam Roof Anchor is designed for fall protection systems on new or existing standing seam roofs. It features twin mounting bars using a total of eight (8) industry-standard S-5 clamps for incredibly secure attachment to standing seams (see instructions for complete list). The clamps will not penetrate the panels or seams, ensuring the roof integrity is not compromised. SKU: 53221 Features Adjustable from 12” to...

Features: Rotating anchor maintains proper SRL orientation angle to connected userFeatures adjustable cradle for DuraTech SRLs and other SRL brands up to 60'.SRL cradle includes D-ring for secondary restraint attachmentIncludes 16D nails and 2-1/2" lag screws for over-ridge installationFor temporary reusable applications on pitched wood roof trusses with sheathingMeets OSHA 1926.502 regulations ...

The Guardian Vertical Beamer 3000 is suitable for installation onto either Vertical or Horizontal I-beams compatible with beams of a wide variety of flange widths and thickness, this Vertical Beamer installs at a fixed position on the beam and is suitable for the connection of either a connecting device or a horizontal lifeline. The Vertical Beamer 3000 can easily be installed by one person without the need for any tools or special equipment, and its durable components allow it to stand up...

The I-Beam Trolley Anchor (Part # A6101) is a Fall Arrest anchor designed to be used in combination with either a shock absorbing lanyard or an SRL. It may also be used for fall restraint and as a work positioning device. Its free moving rollers allow for smooth travel around the work area while always remaining connected. e safety locking toggles allow for easy adjustment and also eliminate the risk of accidental clamp slippage. For use by one worker with a combined weight of up to 310...

The Concrete Anchor Strap is a simple and disposable anchor solution. This lightweight and economical design is equipped with a high strength D-ring.Features: Constructed with heavy duty webbing with wearpadD-Ring connection pointLoop attachment end slips over rebar for easy installation Available in a wide variety of lengths

The industry standard in permanent anchorage devices, the ARS Series anchor has been providing fall protection for the residential and commercial building industry for over 25 years. They are typically installed during the framing stage and then they are flashed into the roofing material as a permanent fixture for the structure. They provide a fall protection tie off point for all tradesmen and maintenance workers. This anchor is available in 2 models – the ARS 2×4 and ARS 2×8. The ARS 2×4 is...

The FallTech 18" Cable Dorsal D-Ring Extender with Steel Snap Hook provides a little more reach for an over the shoulder connection of an SRL or a lanyard. The durable 1/4" galvanized steel cable is swaged with aluminum ferrules to resist rusting. The extender will increase the user's fall clearance distance when using an energy-absorbing lanyard.FEATURES Provides improved over-the-shoulder reach for ease of connecting lanyards and SRLsBuilt with heavy-duty 1/4" galvanized steel cable and...

Hard-wearing 1/4" vinyl coated galvanized steel cable tolerates demanding work environmentsConveniently sized 2" and 3" alloy steel O-rings provide simple pass-through choke-on installation.Smaller O-ring facilitates connection of SRL or lanyardAssembled with steel thimbles and swaged aluminum ferrulesVinyl coating adds a layer of protection and provides easier clean-up

This SRL cradle installs to any Guardian Fall Protection CB post anchor. Accommodates most SRLs up to 50' in length, or up to 65' if used with additional extension attachment. Features: Mounts on top of the CB-12 or CB-18 for retractable Easy installation Swivels 360º Removable and reusable bolt application Cost effective accessory to the CB Does not include CB anchor Please read and understand the manufacturer instructions before using this product.  ...

The Vertical Wall anchors are designed for exterior wall applications as an overhead anchorage device that is nearly invisible from the ground. Fabricated from 11-gauge 430 stainless steel in two models to adapt to varying slope roofs. The install at the wall plate and top chord junction with a single bolt and 4 16d vinyl sinkers that are supplied with each anchor. Perfect for siders, window installers and painters. Can be painted for minimum visual effect. Designed to accommodate the bird...

Features stainless steel anchoring plate with alloy steel connecting D-ringPrecision-cut bushing provides 360° D-ring rotation.Ideally suited for temporary or permanent installation in cured concreteFeatures reusable anchoring plate and D-ring

Drop-Through Cable Anchor, 2' - 8.5' Specialty The Drop-Through Cable Anchor is a versatile anchor point for permanent or temporary use. Simply drop the captive eye and cable through openings in concrete, steel decking, grating or any 1-3/4" hole in a substrate compliant with fall protection requirements Features 8" high visibility green steel plate Forged steel swiveling connection point>/li> 1/4" Steel cable with wear sleeve Accommodate openings from 1.75" to 6" Available in two...

Post Adapter Sleeve for Parapet AnchorProvides secure fit to join Parapet Anchor #7460A and Guardrail Post #6401422.Allows parapet Anchor to also function as a guardrail clamp