OMG Roofing Products

OMG RhinoMark™ Plate Marker is a handheld tool used to identify and mark the location of insulation plates and fasteners beneath roofing membranes. It is commonly used during inspections, repairs, and retrofits where locating existing fasteners is necessary without removing large sections of membrane. The tool allows contractors to quickly mark plate locations for patching, fastening, or system modifications, helping reduce guesswork and minimize unnecessary membrane disturbance. Key features:...

The OMG Lip Termination Bar is designed for securing membrane terminations while providing additional edge control with an integrated lip. This profile helps improve membrane retention at the top edge and creates a more defined termination detail. It is commonly used at vertical transitions, walls, and curb flashings where added edge control is preferred. Key features Integrated lip for improved edge control Provides continuous compression at termination points Helps create a clean, defined...

The OMG CRHD6B is a 6-inch heavy duty roofing fastener in the #14 series designed to secure insulation and membrane to steel, wood, and concrete decks. It features deep thread geometry and a sharp spade-type point for rapid penetration. The fastener is coated with OMG’s CR-10 corrosion-resistant finish and is FM and Miami-Dade approved. Key Features: Deep threads provide high pull-out resistance and secure grip in roofing substrates Sharp 30° spade point allows fast penetration into steel,...

The OMG Flat Termination Bar is designed to secure roofing membranes at terminations, edges, and vertical transitions. It provides a continuous compression point to help hold membrane flashings in place and create a clean termination detail. Commonly used at walls, curbs, and penetrations, the bar is installed with compatible fasteners and sealed along the top edge. Key features Flat profile for standard membrane terminations Provides continuous compression along termination points Used at...

The OMG CRHD9B is a 9-inch #14 heavy duty roofing fastener used to secure insulation and membranes to common roof decks. Deep thread geometry delivers strong pull-out resistance. A 30° spade point speeds penetration, and the CR-10 finish provides corrosion resistance. Key Features: Deep thread profile for high pull-out resistance 30° spade point for fast starts and penetration CR-10 corrosion-resistant coating for durability #3 Phillips truss head compatible with standard screw guns 9-inch...

The OMG RhinoTrac EZ insulation plate is designed for use in mechanically attached commercial roofing systems to secure insulation and membrane assemblies. It provides consistent holding power while helping distribute load across the insulation surface. The plate is used with compatible fasteners to create a secure attachment system for a range of roofing applications. Key features Designed for mechanically attached roofing systems Helps distribute load across insulation surface Compatible...

The OMG RGDP007B is a 7" #12 Standard RoofGrip Drill-Point fastener intended to secure insulation and membranes to steel decks (18-24 gauge) and approved wood decks. It uses deep buttress threads to resist pull-out. The sharp drill point enables penetration through membrane and insulation, and the CR-10 coating protects against corrosion. According to product listings, its thread length is 4", head diameter is 0.435", and it is packaged 1,000 per box. Key Features: Deep buttress thread...

The OMG XHD006B is a 6-inch #15 Extra Heavy Duty roofing fastener designed for attaching insulation and membrane to light gauge steel, OSB, plywood, and aluminum decks. With oversized shank and thread diameters, it offers maximum pull-out resistance. Deep buttress threads reduce pull-out and back-out risks, while the miniature drill point provides quick penetration. The CR-10 coating ensures long-lasting corrosion protection. Key Features: Oversized shank and threads improve pull-out...

The OMG XHD007B is a 7-inch #15 Extra Heavy Duty roofing fastener designed for securing insulation and membrane to light gauge steel, OSB, plywood, and aluminum decks. It features oversized shank and thread diameters for maximum pull-out strength, deep buttress threads for added back-out resistance, and a miniature drill point for quick penetration. The CR-10 coating provides reliable corrosion resistance for long-term performance. Key Features: Oversized shank and thread diameters increase...

The OMG CRH12B is a 12-inch #14 heavy duty roofing fastener for securing insulation and membranes to common roof decks. Deep thread geometry provides strong pull-out resistance. A 30° spade point speeds penetration and the CR-10 finish delivers corrosion resistance. Key Features: Deep thread profile for high pull-out resistance 30° spade point for rapid penetration and fast starts CR-10 corrosion-resistant coating for durability #3 Phillips truss head compatible with standard screw guns...

The OMG SPGA238B-B seam plate is a barbed metal “stress plate” used in commercial roofing to fasten single-ply membranes and accessories. The barbs on the plate help grip membranes or insulation layers, resisting pull-through forces. It is constructed of Galvalume-coated or AZ-coated steel to enhance corrosion resistance while serving as a load-distributing plate for fasteners. Key Features Barbed profile for enhanced grip in membrane layers Steel body with corrosion-resistant coating Round...

The OMG SPGA2 is a 2-inch flat metal seam plate made from Galvalume® coated steel and designed for roofing membrane lap seam fastening. Its round design eliminates sharp corners that could damage membranes or insulation. It works with OMG’s standard, heavy duty, and CD-10 fasteners to help distribute load and maintain secure attachment of roofing membranes. Key Features 2-inch (50 mm) diameter flat stress/seam plate Constructed with Galvalume® coated steel for corrosion resistance Round design...

OB500PT-GUNKIT3 is a replacement gun and hose kit designed for OMG’s canister adhesive systems. It includes a gun assembly with trigger lock and the hose components needed to deliver both adhesive Part 1 and Part 2 reliably. This kit ensures precise, controlled application and makes maintaining or repairing the adhesive dispensing setup easier. Key Features gun assembly with trigger lock to prevent accidental dispensing dual hose assembly for simultaneous flow of Part 1 & Part 2 components...

The OMG OlyFill™ Dual Tank System is a compact two-component foam sealant kit designed for roofing and construction applications. This portable system includes two pressurized cylinders (Part 1 and Part 2) that combine through a dispensing gun and static mixing tip to produce expanding polyurethane foam for filling gaps, voids, and penetrations. The compact tank configuration allows for easier handling and transport compared to larger bulk systems, making it suitable for service crews, smaller...

OMG OlyFill™ Foam Sealant is a one-component expanding polyurethane foam designed to fill gaps, voids, and penetrations in roofing and construction applications. It expands upon application to help seal irregular openings and provide insulation and air sealing around roof penetrations, curb details, and other transitions. OlyFill is commonly used in commercial roofing environments where controlled expansion and gap filling are required prior to flashing or finishing. Once cured, the foam can...

The OMG PaceCart Pro15 is a high-output adhesive dispensing cart designed for commercial roofing crews installing insulation with OMG OlyBond adhesives. The Pro15 is built to handle both 5-gallon Bag-in-Box adhesive packaging and 15-gallon drums, giving contractors more flexibility on larger roofing jobs without needing a separate drum conversion kit. This cart uses variable-speed pumps to help control adhesive output and keep production moving across the roof. It is designed for use with OMG...

OMG OlyGlu™ is a canister-applied membrane adhesive designed for bonding TPO and EPDM roofing membranes in commercial roofing systems. The pressurized canister system allows contractors to apply adhesive quickly and evenly using a hose and spray gun applicator, helping improve installation speed and coverage. OlyGlu is commonly used for field membrane adhesion in single-ply roofing assemblies where controlled spray application is preferred over traditional bucket adhesives. The system is...

OMG OlyGlu™ is a canister-applied membrane adhesive designed for bonding TPO and EPDM roofing membranes in commercial roofing systems. The pressurized canister allows contractors to apply adhesive quickly and evenly using a hose and spray gun applicator. The smaller canister format provides a more compact adhesive solution for smaller roofing areas, service work, and repair applications while still delivering consistent spray coverage and membrane bonding performance. Key features: Designed...

The OMG RGDP158B is a 1-5/8" #12 Standard RoofGrip Drill Point roofing fastener used to attach insulation and membranes to light gauge steel (18–24 gauge) and wood decks. It features a deep buttress thread profile to enhance pull-out resistance. Its extra-sharp drill point enables fast installation, and the CR-10 coating ensures corrosion protection. Key Features: Deep buttress threads for high pull-out resistance Extra-sharp drill point for fast penetration in new and reroof applications #3...

The OMG RGDP214B is a 2¼" #14 Standard RoofGrip Drill Point fastener designed for securing insulation and membranes to light gauge steel and wood decks. It employs deep buttress thread geometry to increase pull-out resistance. A sharp drill point enhances performance even in retrofit applications, and the CR-10 finish provides corrosion protection. Key Features: Deep buttress threads for enhanced pull-out resistance Drill-point design for fast penetration in retrofit or new work #3 Phillips...

The OMG RGDP004B is a 4" #12 Standard RoofGrip Drill Point fastener used to secure insulation and membrane to steel decks (18–24 gauge) and wood decks. It features deep buttress threads to enhance pull-out resistance. The sharp drill point ensures fast penetration in both new and retrofit applications, and the CR-10 coating delivers corrosion protection. Key Features: Deep buttress threads provide superior pull-out resistance Sharp drill point allows quick penetration in new or retrofit...

The OMG RGDP005B is a 5" #12 Standard RoofGrip Drill Point fastener designed to secure insulation and membrane to steel decks (18–24 gauge) and appropriate wood decks. It features deep buttress threads for enhanced pull-out resistance. The drill point design allows efficient penetration even through existing roof systems, and the CR-10 coating offers corrosion resistance. Key Features: Deep buttress threads for strong pull-out resistance Drill point design for ease of installation in new and...

The OMG RGDP008B is an 8" #12 Standard RoofGrip Drill-Point fastener designed to attach roof insulation and membranes to steel (18–24 gauge) and approved wood decks. It uses deep buttress threads to resist pull-out forces. Its sharp drill-point allows for retrofit or new installation, and the CR-10 coating offers durable corrosion protection. Key Features: Deep buttress threads for superior pull-out performance Drill-point design enabling penetration in retrofit or new construction #3 Phillips...

The OMG CR114B Heavy Duty Roofing Fastener is a #14 screw engineered for insulation and membrane attachment in steel, wood, and structural concrete decks. It measures 1¼ inches long with a .245 in thread diameter, full thread design, and CR-10 corrosion-resistant coating. With a #3 Phillips Truss head and spade point, it delivers high pull-out values and secure seating for plates and membranes. Key Features Heavy Duty #14 screw for multiple roof deck types 1¼ in overall length with full thread...

The OMG CR134B Heavy Duty Roofing Fastener is a #14 screw designed to secure roofing insulation or membrane to steel, wood, or structural concrete decks. It features a 1 ¾ in (45 mm) length, .245 in thread diameter, full thread design, and CR-10 corrosion-resistant coating. A #3 Phillips Truss head and 30° spade point enable efficient installation and reliable performance. Key Features 1 ¾ in length for medium substrate thicknesses Full thread for strong engagement CR-10 corrosion-resistant...

The OMG CRH11B is an 11-inch #14 heavy duty roofing fastener designed for use with insulation and membrane systems on steel, wood, and concrete decks. It features deep thread geometry to maximize pull-out resistance. The fastener includes a 30° spade point and CR-10 finish for enhanced performance in roofing environments. Key Features: Deep thread profile for strong grip and pull-out resistance 30° spade point for efficient penetration into substrate CR-10 corrosion resistant coating to...

The OMG CRH14 is a 14-inch #14 heavy duty roofing fastener designed to fasten membrane or insulation through deep roof assemblies. It features aggressive deep thread geometry to maximize pull-out resistance. The 30° spade point ensures easy penetration, while the CR-10 coating offers environmental durability. Key Features: Deep thread design to maximize pull-out strength 30° spade point to allow smooth penetration CR-10 corrosion resistant coating to extend longevity #3 Phillips truss head for...

The OMG CRH16 is a 16-inch #14 heavy duty roofing fastener designed for extra-thick roof insulation and membrane systems. Its deep thread design provides high pull-out resistance. A 30° spade point ensures fast starts and penetration, while the CR-10 finish offers long-lasting corrosion resistance. Key Features: Deep thread profile for high pull-out strength in roof decks 30° spade point allows rapid penetration into substrates CR-10 corrosion-resistant coating reduces rust and extends service...

The OMG CRH18 is an 18-inch #14 heavy duty roofing fastener designed for the thickest insulation and membrane assemblies on steel, wood, and concrete decks. It uses a deep thread profile for exceptional pull-out strength. The 30° spade point ensures fast penetration, and the CR-10 coating provides superior corrosion resistance. Key Features: Deep threads engineered for maximum pull-out resistance 30° spade point for rapid substrate penetration CR-10 corrosion-resistant coating protects against...

The OMG CRHD2B Heavy Duty Roofing Fastener is engineered to secure insulation or membrane to steel, wood, or structural concrete decks. It has a 2-inch length, full thread design, and a CR-10 corrosion-resistant coating that meets FM 4470 standards. Its #3 Phillips truss head and 30° spade point allow for efficient installation and solid engagement. Key Features 2-inch length for thicker assemblies Full thread design for maximum hold CR-10 corrosion-resistant coating meeting FM 4470 #3...

The OMG CRH20 is a 20-inch #14 heavy duty roofing fastener engineered for the thickest insulation and roofing systems. Its deep thread design provides maximum pull-out resistance, while the 30° spade point ensures rapid penetration into steel, wood, or concrete decks. The CR-10 corrosion-resistant coating enhances durability and service life. Key Features: Deep threads designed for high pull-out resistance 30° spade point for fast penetration into substrates CR-10 corrosion-resistant coating...

The OMG CRH22 is a 22-inch #14 heavy duty roofing fastener engineered for the thickest insulation and roofing systems. Its deep thread profile maximizes pull-out resistance, while the 30° spade point delivers quick penetration into steel, wood, and concrete decks. The CR-10 coating provides superior corrosion resistance in demanding environments. Key Features: Deep thread geometry designed for maximum pull-out strength 30° spade point for fast, reliable penetration CR-10 corrosion-resistant...

The OMG CRH24 is a 24-inch #14 heavy duty roofing fastener designed for extremely thick roof insulation and membrane assemblies. Its deep thread geometry ensures superior pull-out resistance, while the 30° spade point provides fast penetration into steel, wood, or concrete. The CR-10 finish delivers long-term corrosion resistance. Key Features: Deep threads maximize pull-out resistance in roofing substrates 30° spade point allows rapid penetration into deck materials CR-10 corrosion-resistant...

The OMG CRHD3B Heavy Duty Roofing Fastener is designed to attach insulation or roofing membranes securely to steel, wood, or structural concrete decks. With a length of 3 in (75 mm), full thread profile, and CR-10 corrosion-resistant finish, it provides reliable performance under demanding conditions. A #3 Phillips truss head and 30° spade point ensure consistent driveability across substrate types. Key Features 3 in length for thicker roof assemblies Full thread design for maximum engagement...

The OMG CRHD7B is a 7-inch heavy duty roofing fastener in the #14 series designed to secure insulation and membranes to steel, wood, and concrete decks. It features a deep thread geometry and a sharp 30° spade point for fast penetration. The fastener is coated with OMG’s CR-10 corrosion resistant finish and is Factory Mutual and Miami-Dade approved. Key Features: Deep thread profile for high pull-out resistance in roofing substrates 30° spade point enables swift penetration into steel, wood,...

The OMG XHD012B is a 12-inch #15 Extra Heavy Duty roofing fastener designed for thick roof assemblies including insulation and membranes attached to light gauge steel, OSB, plywood, or aluminum decks. Its oversized shank and thread diameters maximize pull-out strength. Deep buttress threads reduce back-out risk, while the miniature drill point ensures quick substrate penetration. The CR-10 coating delivers long-term corrosion resistance. Key Features: Oversized shank and threads provide...

The OMG XHD014 is a 14-inch #15 Extra Heavy Duty roofing fastener engineered for securing thick roofing assemblies into light gauge steel, OSB, plywood, or aluminum decks. Its oversized shank and thread diameters maximize pull-out resistance, while deep buttress threads reduce pull-out and back-out. The miniature drill point ensures quick penetration, and the CR-10 coating provides superior corrosion protection. Key Features: Oversized shank and threads provide maximum pull-out strength Deep...

The OMG XHD016 is a 16-inch #15 Extra Heavy Duty roofing fastener designed for very thick roof insulation and membrane assemblies installed into light gauge steel, OSB, plywood, and aluminum decks. Its oversized shank and threads maximize pull-out strength. Deep buttress threads reduce pull-out and back-out, while the miniature drill point provides quick penetration. The CR-10 coating ensures superior corrosion protection. Key Features: Oversized shank and threads provide high pull-out...

The OMG XHD018 is an 18-inch #15 Extra Heavy Duty roofing fastener designed for extra-thick insulation and membrane systems attached to light gauge steel, OSB, plywood, or aluminum decks. Its oversized shank and threads maximize pull-out strength. Deep buttress threads minimize pull-out and back-out, while a miniature drill point ensures quick penetration. The CR-10 coating provides long-term corrosion protection. Key Features: Oversized shank and threads provide superior pull-out resistance...

The OMG XHD002B is part of the XHD (#15) Extra Heavy Duty roofing fastener series designed for light gauge steel, OSB, plywood, or aluminum decks. It features oversized shank and thread diameters plus deep buttress threads to maximize pull-out and back-out resistance. A miniature drill point ensures fast penetration and the CR-10 coating delivers corrosion protection. Key Features: Oversized heavy shank and thread diameters for increased pull-out resistance Deep buttress threads to resist...

The OMG XHD020 is a 20-inch #15 Extra Heavy Duty roofing fastener designed for ultra-thick insulation and membrane assemblies on light gauge steel, OSB, plywood, or aluminum decks. Oversized shank and thread diameters deliver superior pull-out strength, while deep buttress threads reduce back-out. The miniature drill point ensures efficient penetration, and the CR-10 coating protects against corrosion. Key Features: Oversized shank and threads provide maximum pull-out resistance Deep buttress...

The OMG XHD022 is a 22-inch #15 Extra Heavy Duty roofing fastener designed for securing ultra-thick insulation and membrane systems into light gauge steel, OSB, plywood, and aluminum decks. It features oversized shank and thread diameters for superior pull-out resistance, deep buttress threads to reduce pull-out and back-out, and a miniature drill point for quick penetration. The CR-10 coating ensures excellent corrosion resistance. Key Features: Oversized shank and threads deliver superior...

The OMG XHD024 is a 24-inch #15 Extra Heavy Duty roofing fastener designed for extremely thick insulation and membrane assemblies installed into light gauge steel, OSB, plywood, and aluminum decks. Oversized shank and thread diameters provide maximum pull-out strength. Deep buttress threads minimize back-out, while the miniature drill point ensures fast penetration. The CR-10 coating delivers long-lasting corrosion protection. Key Features: Oversized shank and threads provide superior pull-out...

The OMG XHD004B is a 4-inch #15 Extra Heavy Duty roofing fastener designed to secure insulation and membrane into light gauge steel, OSB, plywood, and aluminum decks. Its oversized shank and threads provide high pull-out resistance, while deep buttress threads reduce back-out. A miniature drill point ensures quick penetration, and the CR-10 coating provides proven corrosion resistance. Key Features: Heavy shank and oversized threads for maximum pull-out resistance Deep buttress thread profile...

The OMG XHD008B is an 8-inch #15 Extra Heavy Duty roofing fastener engineered for attaching insulation and membrane into light gauge steel, OSB, plywood, and aluminum decks. Oversized shank and thread diameters maximize pull-out strength, while deep buttress threads reduce pull-out and back-out. The miniature drill point ensures quick penetration and the CR-10 coating protects against corrosion in demanding environments. Key Features: Oversized shank and threads deliver superior pull-out...

RhinoBond TPO Plates are induction-weld plates designed specifically for use with TPO roofing membranes as part of the RhinoBond non-penetrating attachment system. Manufactured from specially coated Galvalume steel, these plates are installed beneath the membrane and bonded using induction welding, eliminating the need for exposed fasteners. The plate’s recessed center and raised bonding surface help ensure consistent weld strength while supporting secure attachment of roof insulation and...

The OB5001-OB5002 set is the 10-gallon Bag-in-Box version of the OMG OlyBond500 two-component, low-rise polyurethane foam adhesive. It includes 5 gallons each of Part 1 and Part 2 adhesive, designed for use with PaceCart, SpotShot applicators, or compatible dispensing tools. It is formulated for new and re-roof applications, delivering rapid adhesion of insulation boards with excellent wind uplift resistance and ultra-low VOC emissions. Key Features Bag-in-Box packaging: 5 gallons Part 1 + 5...