Specials

The OMG CRH11B is an 11-inch #14 heavy duty roofing fastener designed for use with insulation and membrane systems on steel, wood, and concrete decks. It features deep thread geometry to maximize pull-out resistance. The fastener includes a 30° spade point and CR-10 finish for enhanced performance in roofing environments. Key Features: Deep thread profile for strong grip and pull-out resistance 30° spade point for efficient penetration into substrate CR-10 corrosion resistant coating to...

The OMG CRH14 is a 14-inch #14 heavy duty roofing fastener designed to fasten membrane or insulation through deep roof assemblies. It features aggressive deep thread geometry to maximize pull-out resistance. The 30° spade point ensures easy penetration, while the CR-10 coating offers environmental durability. Key Features: Deep thread design to maximize pull-out strength 30° spade point to allow smooth penetration CR-10 corrosion resistant coating to extend longevity #3 Phillips truss head for...

The OMG CRH16 is a 16-inch #14 heavy duty roofing fastener designed for extra-thick roof insulation and membrane systems. Its deep thread design provides high pull-out resistance. A 30° spade point ensures fast starts and penetration, while the CR-10 finish offers long-lasting corrosion resistance. Key Features: Deep thread profile for high pull-out strength in roof decks 30° spade point allows rapid penetration into substrates CR-10 corrosion-resistant coating reduces rust and extends service...

The OMG CRH18 is an 18-inch #14 heavy duty roofing fastener designed for the thickest insulation and membrane assemblies on steel, wood, and concrete decks. It uses a deep thread profile for exceptional pull-out strength. The 30° spade point ensures fast penetration, and the CR-10 coating provides superior corrosion resistance. Key Features: Deep threads engineered for maximum pull-out resistance 30° spade point for rapid substrate penetration CR-10 corrosion-resistant coating protects against...

The OMG CRHD2B Heavy Duty Roofing Fastener is engineered to secure insulation or membrane to steel, wood, or structural concrete decks. It has a 2-inch length, full thread design, and a CR-10 corrosion-resistant coating that meets FM 4470 standards. Its #3 Phillips truss head and 30° spade point allow for efficient installation and solid engagement. Key Features 2-inch length for thicker assemblies Full thread design for maximum hold CR-10 corrosion-resistant coating meeting FM 4470 #3...

The OMG CRH22 is a 22-inch #14 heavy duty roofing fastener engineered for the thickest insulation and roofing systems. Its deep thread profile maximizes pull-out resistance, while the 30° spade point delivers quick penetration into steel, wood, and concrete decks. The CR-10 coating provides superior corrosion resistance in demanding environments. Key Features: Deep thread geometry designed for maximum pull-out strength 30° spade point for fast, reliable penetration CR-10 corrosion-resistant...

The OMG CRH24 is a 24-inch #14 heavy duty roofing fastener designed for extremely thick roof insulation and membrane assemblies. Its deep thread geometry ensures superior pull-out resistance, while the 30° spade point provides fast penetration into steel, wood, or concrete. The CR-10 finish delivers long-term corrosion resistance. Key Features: Deep threads maximize pull-out resistance in roofing substrates 30° spade point allows rapid penetration into deck materials CR-10 corrosion-resistant...

The OMG XHD012B is a 12-inch #15 Extra Heavy Duty roofing fastener designed for thick roof assemblies including insulation and membranes attached to light gauge steel, OSB, plywood, or aluminum decks. Its oversized shank and thread diameters maximize pull-out strength. Deep buttress threads reduce back-out risk, while the miniature drill point ensures quick substrate penetration. The CR-10 coating delivers long-term corrosion resistance. Key Features: Oversized shank and threads provide...

The OMG XHD014 is a 14-inch #15 Extra Heavy Duty roofing fastener engineered for securing thick roofing assemblies into light gauge steel, OSB, plywood, or aluminum decks. Its oversized shank and thread diameters maximize pull-out resistance, while deep buttress threads reduce pull-out and back-out. The miniature drill point ensures quick penetration, and the CR-10 coating provides superior corrosion protection. Key Features: Oversized shank and threads provide maximum pull-out strength Deep...

The OMG XHD016 is a 16-inch #15 Extra Heavy Duty roofing fastener designed for very thick roof insulation and membrane assemblies installed into light gauge steel, OSB, plywood, and aluminum decks. Its oversized shank and threads maximize pull-out strength. Deep buttress threads reduce pull-out and back-out, while the miniature drill point provides quick penetration. The CR-10 coating ensures superior corrosion protection. Key Features: Oversized shank and threads provide high pull-out...

The OMG XHD018 is an 18-inch #15 Extra Heavy Duty roofing fastener designed for extra-thick insulation and membrane systems attached to light gauge steel, OSB, plywood, or aluminum decks. Its oversized shank and threads maximize pull-out strength. Deep buttress threads minimize pull-out and back-out, while a miniature drill point ensures quick penetration. The CR-10 coating provides long-term corrosion protection. Key Features: Oversized shank and threads provide superior pull-out resistance...

The OMG XHD002B is part of the XHD (#15) Extra Heavy Duty roofing fastener series designed for light gauge steel, OSB, plywood, or aluminum decks. It features oversized shank and thread diameters plus deep buttress threads to maximize pull-out and back-out resistance. A miniature drill point ensures fast penetration and the CR-10 coating delivers corrosion protection. Key Features: Oversized heavy shank and thread diameters for increased pull-out resistance Deep buttress threads to resist...

The OMG XHD020 is a 20-inch #15 Extra Heavy Duty roofing fastener designed for ultra-thick insulation and membrane assemblies on light gauge steel, OSB, plywood, or aluminum decks. Oversized shank and thread diameters deliver superior pull-out strength, while deep buttress threads reduce back-out. The miniature drill point ensures efficient penetration, and the CR-10 coating protects against corrosion. Key Features: Oversized shank and threads provide maximum pull-out resistance Deep buttress...

The OMG XHD022 is a 22-inch #15 Extra Heavy Duty roofing fastener designed for securing ultra-thick insulation and membrane systems into light gauge steel, OSB, plywood, and aluminum decks. It features oversized shank and thread diameters for superior pull-out resistance, deep buttress threads to reduce pull-out and back-out, and a miniature drill point for quick penetration. The CR-10 coating ensures excellent corrosion resistance. Key Features: Oversized shank and threads deliver superior...

The OMG XHD024 is a 24-inch #15 Extra Heavy Duty roofing fastener designed for extremely thick insulation and membrane assemblies installed into light gauge steel, OSB, plywood, and aluminum decks. Oversized shank and thread diameters provide maximum pull-out strength. Deep buttress threads minimize back-out, while the miniature drill point ensures fast penetration. The CR-10 coating delivers long-lasting corrosion protection. Key Features: Oversized shank and threads provide superior pull-out...

The OMG XHD004B is a 4-inch #15 Extra Heavy Duty roofing fastener designed to secure insulation and membrane into light gauge steel, OSB, plywood, and aluminum decks. Its oversized shank and threads provide high pull-out resistance, while deep buttress threads reduce back-out. A miniature drill point ensures quick penetration, and the CR-10 coating provides proven corrosion resistance. Key Features: Heavy shank and oversized threads for maximum pull-out resistance Deep buttress thread profile...

The OMG XHD008B is an 8-inch #15 Extra Heavy Duty roofing fastener engineered for attaching insulation and membrane into light gauge steel, OSB, plywood, and aluminum decks. Oversized shank and thread diameters maximize pull-out strength, while deep buttress threads reduce pull-out and back-out. The miniature drill point ensures quick penetration and the CR-10 coating protects against corrosion in demanding environments. Key Features: Oversized shank and threads deliver superior pull-out...

Ideal for use in cold weather work conditions such as construction, word work, refineries, oil drilling, maintenance, mining, etc.Winter Liner w/ Mouthpiece, 2 Layer Cotton Twill/Fleece, Mid Length , Navy Blue, FR Treated, Insulated Ear Barrier, Reflective Strip PIP 364-ML2FMP Features: Mid-length2 layersCotton twill/fleeceSelf extinguishing treated cotton, up to 30 washesInsulated ear barrierSilver reflective stripOne size fits most ...

The Portals Plus Round Adapter for 2 ½″ OD (Item #: POR-14100) is a retrofit component used to adapt round roof penetrations approximately 2.5 inches outer diameter into a compatible retrofit flashing boot. It is installed by fitting around the projection, seating into the correct step of the boot (boot not included), and tightening a clamp (not included) to achieve a watertight seal. This approach lets installers handle non-standard penetrations without full custom boot fabrication. Key...

The Portals Plus Round Adapter for 3 in. OD (Item #: POR-14120) is designed to flash small or non-standard roof penetrations by adapting a 3-inch outer-diameter projection to a compatible retrofit boot. The adapter fits around the penetration, seats into the appropriate step of the retrofit boot, and is then tightened with a clamp (boot and clamp not included). This provides a positive, secure method for flashing irregular shapes. Key features: Adapts 3″ OD penetrations to compatible retrofit...

The Portwest FD04 Apex Composite Mid Boot in black is built for rugged work environments that demand safety, durability, and comfort. Its nubuck leather upper offers long-lasting wear while resisting water penetration. A heat resistant outsole and engineered tread pattern provide traction on uneven ground and resist fuel, oil, and water exposure. The lightweight composite toe cap and puncture resistant non-metallic midsole help protect against impact and underfoot hazards. A convenient quick...

The Portwest HA15 Hi-Vis Ranger Hat in yellow is a high-visibility outdoor safety hat designed for comfort and enhanced visibility in warm weather environments. Constructed with a wide brim and breathable mesh panels, it helps keep wearers cool while providing sun protection. An adjustable drawcord allows a secure, customized fit, and silver reflective tape with contrast material enhances visibility in low-light conditions. This hat meets ANSI/ISEA 107:2015 compliance for high-visibility...

The Portwest PS43 HV Extreme Ear Muffs in gray deliver high-performance hearing protection for noisy environments such as construction sites, manufacturing facilities, and other industrial settings. Designed with a PU-padded headband and dual-pin adjustable ear cups, these ear muffs provide a secure, comfortable fit even during extended wear. Excellent noise attenuation performance helps reduce harmful sound exposure while reflective trim enhances visibility for added safety.  Key...

The Powerblanket 2-Gallon Bucket Heater is engineered to maintain the viscosity and thermal consistency of temperature-sensitive materials in standard 2-gallon containers. It features a patented full-surface wrap design that eliminates hot and cold spots and is compatible with both poly and steel buckets. Models are available for 120 V or 240 V operation and include optional adjustable or fixed thermostats for precise temperature control. Key features: Full-coverage wrap design for uniform...

Features: Cuts straight and wide curves when trimming light gauge stock. For plumbing, heating, air conditioning and roofing trades Blades individually hand edged for maximum cutting efficiency Available in 8", 10" and 12" Size

This Razor-Back digging shovel used for all construction, lawn and garden work. It is the highest quality garden tool. It is ideal for a variety of uses, such as digging, planting, cutting sod and small roots. A heavy-duty, forged-steel digging shovel with a 48″ hardwood handle and a cushioned grip. It features SuperSocket™ reinforcement and a large PowerStep™ for better leverage and comfort. Heavy gauge, tempered-steel blade for maximum strength, extremely sturdy forged steel blade that...

The Razor‑Back 48″ wood-handle shovel (model 2593700) offers excellent quality for its price. It’s heavy-duty enough for tough outdoor chores, backed by warranty, and appreciated by users—especially when well-maintained. This shovel is an essential part of any tool assortment. Ideal for lifting and moving heavy loads of rock, soil and other materials. Designed to transport loose material, such as soil, sand and gravel.For transferring heavy, loose material48" North American Hardwood...

The SafeWaze FS811-4 Cross Arm Strap is a lightweight, reusable anchorage solution designed for tie-off on structural beams or cross-arm configurations. Featuring durable polyester tubular webbing and two pass-through D‑rings, it installs quickly without hardware and provides a mobile fall arrest anchor point wherever needed.

Replacement chalkline cord

Replacement line for Reel fast chalk line

The Tomahawk TG12000iT is a tri-fuel inverter generator designed to deliver stable power for jobsites, backup power, and equipment use. It runs on gasoline, propane (LPG), or natural gas and features inverter technology for clean, consistent power suitable for sensitive electronics. The unit includes electric start, a digital display for real-time monitoring, and a wheel kit with locking handle for mobility. Key features Tri-fuel capability: gasoline, LPG, and natural gas Inverter technology...

The Van Mark T1050 Trim-A-Brake II is a 10 ft. 6 in. portable siding brake built for contractors who need dependable, jobsite-ready bending performance without the extra weight of heavier brakes. Designed to handle trim coil, fascia, and flashing, the T1050 delivers crisp, repeatable bends for windows, doors, soffits, fascia wraps, and custom flashing profiles. Its user-friendly design, smooth operation, and durable construction make it an excellent choice for exterior remodelers, siding...

The Albion B26T600 is a 600 Series B-Line manual multi-component cartridge gun designed for 600 mL side-by-side packs in both 1:1 and 2:1 ratios. A high-thrust 26:1 smooth-rod drive multiplies hand force for pushing medium to thicker two-part epoxies, acrylics/MMA, and polyurethanes through static mixers with clean starts and consistent flow. The rigid frame and synchronized plungers help maintain mix accuracy, while the full-size handle and ladder hook improve ergonomics and staging on long...

The Capital Safety AB17530 Protecta First 5-Point Harness is a full-body safety harness sized XL. It features a rear D-ring attachment point, pass-through buckles at the chest and legs, and 1.75″ wide polyester webbing in blue with yellow underside. This harness includes a padded back plaque and five adjustment points to help achieve a secure fit. All information is taken directly from the manufacturer product page. Key Features Full-body safety harness with five adjustment pointsRear...

CNS130 Cooling Hard Hat Pad Evaporative cooling material provides hours of heat stress reliefEvaporative cooling material keeps you cool for hoursKeeps your head cool and blocks sun from your neckMade from soft quilted hi-vis material for greater visibilityFits on the suspension of a hard hat with hook and loop closuresTo activate, soak in cool water for 2-5 minutesReusable – just reactivateOne size fits al ...

CNS140 Cooling Hard Hat Pad & Neck Shade - Orange Evaporative cooling material keeps you cool for hoursKeeps your head cool and blocks sun from your neckMade from soft quilted hi-vis material for greater visibilityFits on the suspension of a hard hat with hook and loop closuresTo activate, soak in cool water for 2-5 minutesReusable – just reactivateOne size fits all

CSK111 Cooling Skull Cap Liner - BlackMade from moisture wicking soft fabricTraps sweat, keeping it out of your eyesFits under hard hatsOne size fits mostMaterial rated UPF 45

Features: Elastic chin strap with chin cup for a comfortable fitQuick clips design for easy installation on most hard hats on the marketAdjustable buckle on both sides to make length adjustment easy Packaging:  Bag: 12pcs Specs: Dims: 33cm x 4.5cm x 2.5cmCup: 8cm x 4cm x 2.5cmweight: 14g Component:  Elastic Band Chin Cup and ClipsBuckle  Material: Rubber, TC FabricHigh Density PE POM  ...

Middle layer of foamPatented style easily attaches to hard hat suspension with fold over clipsOriginal 8MM thickness

The Van Mark UNL2 UniLeg is a heavy-duty center support leg designed to give your TrimMaster brake a more solid, stable feel across its full working length. Installed under the middle of the brake, it adds a crucial third support point that helps reduce sag, flex, and bounce when you’re bending long runs of fascia, drip edge, and custom trim. Whether you’re set up on stands, sawhorses, or a custom bench, the UNL2 helps keep your brake level, your bends more accurate, and your crew more...