Specials

The Albion E12Q is a 12-volt cordless 1-quart (28–32 oz) cartridge gun designed for fast, controlled dispensing of high-volume cartridges. A variable-speed trigger and top-mounted speed dial regulate flow, while auto-reverse briefly backs off pressure at trigger release to minimize ooze and stringing. The lightweight swivel half-barrel carriage keeps the nozzle oriented through corners and long runs, and jobsite conveniences—built-in puncture wire, ladder hook, and a comfortable over-molded...

The OMG CRHD7B is a 7-inch heavy duty roofing fastener in the #14 series designed to secure insulation and membranes to steel, wood, and concrete decks. It features a deep thread geometry and a sharp 30° spade point for fast penetration. The fastener is coated with OMG’s CR-10 corrosion resistant finish and is Factory Mutual and Miami-Dade approved. Key Features: Deep thread profile for high pull-out resistance in roofing substrates 30° spade point enables swift penetration into steel, wood,...

The WP3012-42-DOME is the replacement cast-iron dome designed for the Wade 3012 roof drain. It provides a durable protective cover that helps prevent debris, gravel, and roofing material from entering the drain body while maintaining efficient rooftop water flow. Built from heavy-duty cast iron, this dome is engineered for long service life in commercial and industrial roofing environments. It is the correct OEM replacement for the Wade 3012 drain series.

The OMG CRH10B is a 10-inch #14 heavy duty roofing fastener engineered to secure insulation and membranes to structural decks. It has deep threads to enhance pull-out resistance. The CR-10 finish provides corrosion protection, and its spade point enables effective penetration. Key Features: Deep thread profile for high pull-out resistance 30° spade point for swift penetration CR-10 corrosion-resistant coating to protect from environmental exposure #3 Phillips truss head compatible with...

Residential Guardrail Gable/Rake System meets or exceeds OSHA standards. It is adjustable from flat roof up to a 16:12 pitch. The system includes one roof bracket, one toeboard bracket, one leg insert, and one upright. It can be used to collect debris for removal during shingle installation. Key features: Meets or exceeds OSHA standards  Adjustable from flat roof up to 16:12 pitch  Includes: 1 roof bracket, 1 toeboard bracket, 1 leg insert, 1 upright  Can be used to catch debris...

The OMG SPGA2 is a 2-inch flat metal seam plate made from Galvalume® coated steel and designed for roofing membrane lap seam fastening. Its round design eliminates sharp corners that could damage membranes or insulation. It works with OMG’s standard, heavy duty, and CD-10 fasteners to help distribute load and maintain secure attachment of roofing membranes. Key Features 2-inch (50 mm) diameter flat stress/seam plate Constructed with Galvalume® coated steel for corrosion resistance Round design...

The FallTech 7428 Cable Pass-Through Sling Anchor is made for creating fast, reusable anchorage points on properly rated structural members such as I-beams. It uses a ¼-inch vinyl-coated galvanized steel cable for durability in tough job-site environments, alloy-steel O-rings designed for pass-through choke-on installation (including a smaller O-ring for SRL or lanyard connection), and swaged aluminum ferrules with steel thimbles. The vinyl coating adds protection from abrasion and easy...

With sleek styling, easy blade replacement, and original-style handles, Malco’s 12″ or 14" Andy Classic snips are a perfect addition to any tool bag. These snips are ideal for cutting vinyl siding, aluminum, copper, or sheet metal. The sleek head design enhances maneuverability, making it easier to cut materials like J-Channel. A full 3″ (76.2 mm) cutting length makes straight shearing with the Malco Andy™ Snip fast and easy. Pressure-fit inset blades allow for easy replacement while in...

The OMG XHD005B is a 5-inch #15 Extra Heavy Duty roofing fastener designed to secure insulation and membrane to light gauge steel, OSB, plywood, and aluminum decks. It features oversized shank and thread diameters for maximum pull-out strength. Deep buttress threads reduce back-out, while the miniature drill point provides quick penetration. The CR-10 coating delivers superior corrosion resistance. Key Features: Oversized shank and thread diameters improve pull-out resistance Deep buttress...

The OMG RGDP003B is a 3" #12 Standard RoofGrip Drill Point fastener designed to attach insulation and membranes to steel decks (18–24 gauge) and wood decks. It features deep buttress threads that enhance pull-out resistance. The extra sharp drill point allows use in retrofit and new construction, while the CR-10 coating provides corrosion protection. Key Features: Deep buttress threads for high pull-out resistance Extra sharp drill point for efficient penetration #3 Phillips truss head design...

The Portals Plus 14310 Square Tube Adapter for 3 × 3 in is designed to seal square steel-tube roof penetrations without disconnecting the penetration. It provides a retrofit flashing solution whereby the adapter fits around the square projection, seats into a compatible boot, and retains joint movement while maintaining a weather-tight seal. The molded EPDM material is resistant to ozone and UV degradation and supports a service range from –60 °F to +270 °F. Key features: Adapts 3 × 3 in...

The Portals Plus Round Adapter for 1 in OD (Item #: POR-14040) is designed to integrate non-standard or irregular roof penetrations of approximately one-inch outer diameter into a compatible retrofit flashing boot. The adapter fits around the projection, seats into an appropriate step of the boot (boot not included), and is secured via a clamp (not included). This solution enables flashing integrity without custom fabrication and ensures a positive, secure seal around unusual roof...

The Portals Plus Round Adapter for 1-1/4 in. OD (Item #: POR-14050) is designed for sealing smaller irregular or non-standard roof penetrations by adapting a 1-1/4″ outside diameter projection into a compatible retrofit flashing boot. The adapter slips around the projection, seats into the appropriate step of the retrofit boot (boot not included) and then the clamp is tightened (clamp not included) to create a secure watertight seal. This method helps avoid custom boot fabrication for odd...

The Portals Plus Round Adapter for 2 in. outer diameter (Item #: POR-14080) is designed for flashing unusual or non-standard roof penetrations by adapting a 2″ OD projection into a retrofit boot. The adapter fits around the penetration and is inserted into the proper step of the retrofit boot (boot not included); final sealing is achieved by tightening a clamp (not included). This product provides a cost-effective way to use existing boot systems rather than fabricating custom flashings. Key...

The Portals Plus Round Adapter for 7/8 in. OD (Item #: POR-13040) is designed for flashing irregular or non-standard roof penetrations by fitting around a 7/8-inch outer diameter projection and seating into a compatible retrofit boot. The adapter is secured by a clamp (not included) to ensure a watertight seal around the penetration. This solution allows use of existing boots rather than custom fabrications. Key features: Designed to accommodate 7/8″ outer diameter penetrations that standard...

Portals Plus 13010 Small Round Adapter is designed for flashing non-standard, small penetrations by adapting a 3/8-inch OD projection to a compatible retrofit boot. It provides a positive, secure flashing method for unusual shapes by fitting around the penetration and seating into the appropriate step of the retrofit boot. Final sealing is achieved by tightening a clamp over the boot and adapter for a snug fit. Key features: Adapts small or unusual 3/8″ OD penetrations to a compatible retrofit...

The Albion 360-1 Core Air-Powered Cartridge Gun is a professional 1/10-gallon (10 oz) pneumatic dispenser engineered for smooth, low-fatigue bead control. Its air valve provides instant on/off flow that reduces stringing, while an adjustable regulator on the line lets you match output to material viscosity and nozzle size. A swivel half-barrel carriage improves access around corners and detail work, and the rigid frame keeps the plunger aligned for clean starts, consistent bead size, and fast...

The AMES Telescoping Snow Roof Rake (model 193055510) is a durable, lightweight solution for safely removing snow from rooftops without needing to climb. Featuring a push-button telescoping aluminum handle that extends up to 17 feet, this tool offers extended reach with stability. A 24-inch poly blade and non-slip grip ensure efficient snow removal and confident handling. The sleek, collapsible design allows for compact storage during off-season months, making it both effective and convenient. ...

The Capital Safety 7241181 Concrete Bolt 4-Pack is a fastener kit used to secure rooftop anchor points into concrete substrates. The kit includes four 12 in (30.5 cm) concrete bolts constructed from rugged, corrosion-resistant steel for durability in industrial jobsite conditions. These fasteners are intended for use with compatible rooftop anchor systems and are suitable for applications in both solid and hollow concrete. Key Features Four 12 in (30.5 cm) concrete bolts for anchoring rooftop...

DeWalt Bi-Flex™ Phillips Pan Head Self-Drilling Screws are engineered for superior performance in metal-to-metal applications. These fasteners feature a self-drilling point that eliminates the need for pre-drilling, helping save time on the job. Designed with a hardened steel shank and Bi-Flex™ corrosion-resistant coating, they provide durability and strength in harsh environments. Ideal for HVAC, electrical, and general metal construction projects, these screws deliver consistent drive...

The Bi-Flex® Bi-Metal Self-Drilling Structural Screw combines the superior corrosion resistance of 300 series stainless steel with the drilling efficiency of carbon steel. Featuring a Phillips pancake head for a low-profile finish, these screws are ideal for steel-to-steel, aluminum-to-steel, aluminum-to-aluminum, and wood-to-steel connections. The Stalgard® GB coating enhances galvanic compatibility in dissimilar metal applications, including those involving aluminum. Designed for high...

DEWALT Bi-Flex® Phillips Flat Head with Wings screws are bi-metal self-drilling structural fasteners designed for efficient wood-to-metal installations. Featuring a corrosion-resistant 300-series stainless-steel shank and head paired with a hardened carbon-steel drill point, these screws deliver long-lasting performance in outdoor and high-moisture environments. The integrated cutting wings create clearance holes through wood or composite materials before breaking off as the drill point...

DEWALT Bi-Flex® Phillips Undercut Flat Head Bi-Metal Self-Drilling Structural Screws deliver the corrosion resistance of 300-series stainless steel with the drilling efficiency of hardened carbon steel. Designed for steel-to-steel, aluminum-to-aluminum, aluminum-to-steel, and wood-to-steel connections, these fasteners feature Stalgard® GB coating for enhanced galvanic compatibility in dissimilar metal applications and increased protection in outdoor or high-moisture environments. The undercut...

DeWalt Bi-Flex® Self-Drilling Metal Screws are engineered for reliable, high-performance fastening in metal-to-metal applications. Whether you're installing steel framing, metal roofing panels, or structural decking, these hex washer head screws deliver consistent drive, secure holding power, and long-lasting durability. Manufactured with precision-formed drill points (#2, #3, and #5), DeWalt Bi-Flex® fasteners eliminate the need for pre-drilling—saving time on job sites. Each screw is coated...

DEWALT Dril‑Flex® Self‑Drilling Structural Screws are dual heat‑treated tapping fasteners engineered for reliable steel‑to‑steel connections in demanding building‑envelope and light‑structural applications. A high‑hardness #2–#5 drill point with lead threads speeds drilling and tapping, while a lower‑hardness load‑bearing section improves ductility and reduces susceptibility to hydrogen‑assisted stress corrosion cracking versus case‑hardened alternatives. Stalgard® and Stalgard® SUB coatings...

Dril-Flex® Self-Drilling Structural Screws combine dual heat treatment with a self-drilling, self-tapping design to deliver the strength, ductility, and resistance to embrittlement required for critical connections. The Phillips undercut flat head seats flush where clearance matters and provides a clean, low-profile finish. Stalgard® coating improves corrosion resistance and galvanic compatibility in dissimilar-metal applications, while the hardened drilling point and lead threads speed...

Drilit® self-drilling fasteners eliminate separate drilling and tapping for faster, more economical installations. This Extended Drilling Capacity variant uses higher-capacity drill points (#5) to penetrate thicker steel in a single pass. A hex washer head provides a stable bearing surface and positive drive, while Stalgard® / Gray Stalgard® finishes deliver proven corrosion resistance (ASTM B117 ~1,000 hours). Select sizes are offered with EPDM bonded sealing washers for weather-tight...

Drilit® self-drilling fasteners eliminate separate drilling and tapping for faster, more economical installations. This variant pairs a hex washer head with an EPDM bonded sealing washer to create a reliable, weather-tight seal under metal panels and trims. Available with Stalgard® and Gray Stalgard® corrosion-resistant finishes (typically no red rust after ~1,000 hours per ASTM B117), these screws deliver durable performance in exterior and mixed-material assemblies. Gray Stalgard® is also...

Drilit® self-drilling fasteners eliminate separate drilling and tapping for faster, more economical installations. The hex washer head provides positive drive and bearing surface for reliable seating, while the integrated self-drilling point speeds penetration in steel and other common substrates. Available with Stalgard® and Gray Stalgard® corrosion-resistant finishes (ASTM B117 ~1,000-hour salt-spray performance), and in select sizes with EPDM bonded sealing washers for a weather-tight seal....

Tap-Flex® Thread-Forming Structural Screws are engineered for high-performance fastening in demanding structural and curtain wall applications. Designed to replace traditional nut and bolt assemblies, these dual heat-treated self-tapping fasteners provide the strength, ductility, and corrosion resistance required for long-term reliability. Featuring the patented E-Form® segmented thread profile, Tap-Flex® screws reduce drive torque, improve installation efficiency, and form threads that ensure...

TapFast fasteners are engineered for attaching light-gauge metal panels (up to 18 ga) to wood frame structures. Featuring a hex washer head paired with an aluminum EPDM bonded sealing washer for a reliable, weather-tight seal, TapFast delivers strong pull-out performance in wood while easily penetrating multiple panel thicknesses. The high-low thread design improves driving efficiency and holding power, and the Stalgard coating provides superior corrosion resistance versus standard zinc...

The FallTech 7080BM Advanced ComforTech Gel 1D Standard Non-Belted Full Body Harness is designed for professional fall-arrest applications that demand comfort and durability. It features shoulder-yoke and sub-pelvic leg pads with a gel endoskeleton for enhanced comfort, a lightweight forged aluminum alloy dorsal D-ring, nine-grommet tongue-buckle leg adjustment, a quick-connect chest buckle with visual indicator, and a fully adjustable suspension trauma relief system. The non-belted 1-D-ring...

The Glazelock GLZ01 interlocking horseshoe plastic shim is designed for precision leveling and alignment tasks in window, door, curtain wall and general construction applications. Each shim measures 3 in in length, 1½ in in width and ¼ in thick, with a ½ in slot to accommodate bolts or anchors. These shims are made from durable plastic that resists rotting, shrinking or swelling and feature a patented collapsible locking mechanism for stackable placement. They help reduce labor and material...

The Glazelock GLZ02 interlocking horseshoe plastic shim is designed for precision leveling and alignment in window, door, curtain wall and general construction applications. Each shim measures 3″ in length, 1½″ in width and ⅛″ in thickness, with a ½″ slot to accommodate bolts or anchors. These shims are made from durable structural plastic that resists rot, shrink and swell, and they feature a patented collapsible locking mechanism allowing secure stackable placement. They help reduce labor...

The Glazelock GLZ03 interlocking horseshoe plastic shim is engineered for precision leveling and alignment in window, door, curtain wall and general construction settings. Each shim measures 3" in length, 1-1/2" in width and 1/16" in thickness, and includes a 1/2" slot to accommodate bolts or anchors. These shims are made from structural plastic that resists rot, shrink and swell, and they feature a stackable interlocking design to eliminate the need for tape or glue when achieving exact...

The H.B. Fuller Millennium EPDM Flashing Tape is a flexible, uncured EPDM membrane laminated to a 25 mil pressure-sensitive adhesive. Designed for rooftop flashing applications, it eliminates the need for torch or liquid adhesives while providing strong, watertight adhesion. Available in four roll widths (5″, 6″, 9″, 12″), the ET-0553 series is engineered to resist shrinkage, delamination, and environmental movement in roofing systems. Key Features Flexible uncured EPDM membrane with adhesive...

A reflective aluminum‑enhanced roof coating—Karnak 27 Fibered Perfectseal forms a metallic shield atop your roof surface, reflecting sunlight to protect underlying asphaltic materials from heat degradation. Infused with reinforcing fibers, it offers steadfast adhesion and thermal resistance, reducing repairs and extending roof lifespan while helping lower building temperatures during hot seasons. Key Features Forms a reflective, self-protecting shield by aluminum flake leafing to the surface...

The Occunomix Class 3 Speed Collection Premium Breathable Rain Jacket includes an internal storm flap, a hideaway hood, and a hook and loop sleeve strap. This rain jacket is made of 100% polyester, 300 denier maximum breathable waterproof PU and PTFE bicomponent transfer laminate membrane, with sealed seams poly cotton liner. The two horizontal stripes and four horizontal sleeve stripes on this jacket are made of 2" 3M Scotchlite reflective material. One pocket on this rain jacket is located...

OB500-15A and OB500-15B are the two drum components of OMG’s OlyBond500 roof insulation adhesive. The Part 1 drum (OB500-15A) contains one half of the system, while the Part 2 drum (OB500-15B) completes the system when mixed. When applied, the adhesive rises quickly, curing in 4 to 8 minutes depending on weather, to secure insulation board to deck or cover board in new construction or re-roofing applications. Key Features two-component polyurethane adhesive system (Part 1 & Part 2) fast tack...

The OMG PaceCart Pro15 is a high-output adhesive dispensing cart designed for commercial roofing crews installing insulation with OMG OlyBond adhesives. The Pro15 is built to handle both 5-gallon Bag-in-Box adhesive packaging and 15-gallon drums, giving contractors more flexibility on larger roofing jobs without needing a separate drum conversion kit. This cart uses variable-speed pumps to help control adhesive output and keep production moving across the roof. It is designed for use with OMG...

The OMG Hercules-Plus Aluminum RetroDrain with Vortex Breaker is a high-performance retrofit drain available in 3-inch, 4-inch, 5-inch, and 6-inch models (HDAL3V–HDAL6V). It combines a one-piece spun aluminum body with a large flange and the innovative vortex breaker dome for up to 2.5× greater flow than standard designs. The drain installs from the rooftop without disturbing existing plumbing and includes OMG’s watertight U-Flow mechanical seal for connection to existing pipes. Its safety...

The legion of HDTPO3V, HDTPO4V, HDTPO5V, HDTPO6V comprises the TPO-flanged versions of OMG’s Hercules-Plus Vortex Breaker RetroDrains, spanning 3-inch through 6-inch sizes. These drains combine durable spun aluminum bodies with a TPO-coated flange for direct membrane welding, and include the integrated vortex breaker dome to boost flow (up to 2.5×). Each unit also includes the U-Flow mechanical seal for a watertight connection to existing piping, enabling rooftop retrofit without disturbing...

The OMG RGDP158B is a 1-5/8" #12 Standard RoofGrip Drill Point roofing fastener used to attach insulation and membranes to light gauge steel (18–24 gauge) and wood decks. It features a deep buttress thread profile to enhance pull-out resistance. Its extra-sharp drill point enables fast installation, and the CR-10 coating ensures corrosion protection. Key Features: Deep buttress threads for high pull-out resistance Extra-sharp drill point for fast penetration in new and reroof applications #3...

The OMG RGDP214B is a 2¼" #14 Standard RoofGrip Drill Point fastener designed for securing insulation and membranes to light gauge steel and wood decks. It employs deep buttress thread geometry to increase pull-out resistance. A sharp drill point enhances performance even in retrofit applications, and the CR-10 finish provides corrosion protection. Key Features: Deep buttress threads for enhanced pull-out resistance Drill-point design for fast penetration in retrofit or new work #3 Phillips...

The OMG CR114B Heavy Duty Roofing Fastener is a #14 screw engineered for insulation and membrane attachment in steel, wood, and structural concrete decks. It measures 1¼ inches long with a .245 in thread diameter, full thread design, and CR-10 corrosion-resistant coating. With a #3 Phillips Truss head and spade point, it delivers high pull-out values and secure seating for plates and membranes. Key Features Heavy Duty #14 screw for multiple roof deck types 1¼ in overall length with full thread...

The OMG CR134B Heavy Duty Roofing Fastener is a #14 screw designed to secure roofing insulation or membrane to steel, wood, or structural concrete decks. It features a 1 ¾ in (45 mm) length, .245 in thread diameter, full thread design, and CR-10 corrosion-resistant coating. A #3 Phillips Truss head and 30° spade point enable efficient installation and reliable performance. Key Features 1 ¾ in length for medium substrate thicknesses Full thread for strong engagement CR-10 corrosion-resistant...

The OMG CRH11B is an 11-inch #14 heavy duty roofing fastener designed for use with insulation and membrane systems on steel, wood, and concrete decks. It features deep thread geometry to maximize pull-out resistance. The fastener includes a 30° spade point and CR-10 finish for enhanced performance in roofing environments. Key Features: Deep thread profile for strong grip and pull-out resistance 30° spade point for efficient penetration into substrate CR-10 corrosion resistant coating to...