Clearance Specials

The Portals Plus 14310 Square Tube Adapter for 3 × 3 in is designed to seal square steel-tube roof penetrations without disconnecting the penetration. It provides a retrofit flashing solution whereby the adapter fits around the square projection, seats into a compatible boot, and retains joint movement while maintaining a weather-tight seal. The molded EPDM material is resistant to ozone and UV degradation and supports a service range from –60 °F to +270 °F. Key features: Adapts 3 × 3 in...

The Portals Plus Round Adapter for 1 in OD (Item #: POR-14040) is designed to integrate non-standard or irregular roof penetrations of approximately one-inch outer diameter into a compatible retrofit flashing boot. The adapter fits around the projection, seats into an appropriate step of the boot (boot not included), and is secured via a clamp (not included). This solution enables flashing integrity without custom fabrication and ensures a positive, secure seal around unusual roof...

The Portals Plus Round Adapter for 1-1/4 in. OD (Item #: POR-14050) is designed for sealing smaller irregular or non-standard roof penetrations by adapting a 1-1/4″ outside diameter projection into a compatible retrofit flashing boot. The adapter slips around the projection, seats into the appropriate step of the retrofit boot (boot not included) and then the clamp is tightened (clamp not included) to create a secure watertight seal. This method helps avoid custom boot fabrication for odd...

The Portals Plus Round Adapter for 2 in. outer diameter (Item #: POR-14080) is designed for flashing unusual or non-standard roof penetrations by adapting a 2″ OD projection into a retrofit boot. The adapter fits around the penetration and is inserted into the proper step of the retrofit boot (boot not included); final sealing is achieved by tightening a clamp (not included). This product provides a cost-effective way to use existing boot systems rather than fabricating custom flashings. Key...

The Portals Plus Round Adapter for 7/8 in. OD (Item #: POR-13040) is designed for flashing irregular or non-standard roof penetrations by fitting around a 7/8-inch outer diameter projection and seating into a compatible retrofit boot. The adapter is secured by a clamp (not included) to ensure a watertight seal around the penetration. This solution allows use of existing boots rather than custom fabrications. Key features: Designed to accommodate 7/8″ outer diameter penetrations that standard...

Portals Plus 13010 Small Round Adapter is designed for flashing non-standard, small penetrations by adapting a 3/8-inch OD projection to a compatible retrofit boot. It provides a positive, secure flashing method for unusual shapes by fitting around the penetration and seating into the appropriate step of the retrofit boot. Final sealing is achieved by tightening a clamp over the boot and adapter for a snug fit. Key features: Adapts small or unusual 3/8″ OD penetrations to a compatible retrofit...

The Albion 360-1 Core Air-Powered Cartridge Gun is a professional 1/10-gallon (10 oz) pneumatic dispenser engineered for smooth, low-fatigue bead control. Its air valve provides instant on/off flow that reduces stringing, while an adjustable regulator on the line lets you match output to material viscosity and nozzle size. A swivel half-barrel carriage improves access around corners and detail work, and the rigid frame keeps the plunger aligned for clean starts, consistent bead size, and fast...

The Capital Safety 7241181 Concrete Bolt 4-Pack is a fastener kit used to secure rooftop anchor points into concrete substrates. The kit includes four 12 in (30.5 cm) concrete bolts constructed from rugged, corrosion-resistant steel for durability in industrial jobsite conditions. These fasteners are intended for use with compatible rooftop anchor systems and are suitable for applications in both solid and hollow concrete. Key Features Four 12 in (30.5 cm) concrete bolts for anchoring rooftop...

The Portals Plus Round Adapter for 2 ½″ OD (Item #: POR-14100) is a retrofit component used to adapt round roof penetrations approximately 2.5 inches outer diameter into a compatible retrofit flashing boot. It is installed by fitting around the projection, seating into the correct step of the boot (boot not included), and tightening a clamp (not included) to achieve a watertight seal. This approach lets installers handle non-standard penetrations without full custom boot fabrication. Key...

The Portals Plus Round Adapter for 3 in. OD (Item #: POR-14120) is designed to flash small or non-standard roof penetrations by adapting a 3-inch outer-diameter projection to a compatible retrofit boot. The adapter fits around the penetration, seats into the appropriate step of the retrofit boot, and is then tightened with a clamp (boot and clamp not included). This provides a positive, secure method for flashing irregular shapes. Key features: Adapts 3″ OD penetrations to compatible retrofit...

Replacement chalkline cord

Replacement line for Reel fast chalk line

The Capital Safety AB17530 Protecta First 5-Point Harness is a full-body safety harness sized XL. It features a rear D-ring attachment point, pass-through buckles at the chest and legs, and 1.75″ wide polyester webbing in blue with yellow underside. This harness includes a padded back plaque and five adjustment points to help achieve a secure fit. All information is taken directly from the manufacturer product page. Key Features Full-body safety harness with five adjustment pointsRear...

Features: Elastic chin strap with chin cup for a comfortable fitQuick clips design for easy installation on most hard hats on the marketAdjustable buckle on both sides to make length adjustment easy Packaging:  Bag: 12pcs Specs: Dims: 33cm x 4.5cm x 2.5cmCup: 8cm x 4cm x 2.5cmweight: 14g Component:  Elastic Band Chin Cup and ClipsBuckle  Material: Rubber, TC FabricHigh Density PE POM  ...

Middle layer of foamPatented style easily attaches to hard hat suspension with fold over clipsOriginal 8MM thickness