The Portals Plus Medium Pipe Boot White TPO 1″-6″ (POR-46209) is designed for single-pipe roof penetrations up to 6″ in diameter. It features a 70 mil TPO injection-molded body and includes an integrated Snaplock stainless steel clamp for securing the boot to the pipe. A compression-molded 60 mil EPDM or Neoprene body is included depending on base. It may be adapted for square tubing or angle-iron through optional adapters. This boot is suitable for use with TPO roofing membranes and is white...

Portals Plus 29430 is a five-hole Pipe Portal flashing cover that includes five C-555 black EPDM caps and stainless steel clamps. Designed for sealing multiple roof penetrations, it features precut port holes and molded sealing ribs for faster installation and a long-lasting, watertight connection. The EPDM rubber is resistant to ozone and UV rays and offers a wide service temperature range from −60°F to +270°F. This assembly is used in conjunction with a compatible roof curb to ensure secure...

The Portals Plus 32015 Curb Cover w/ C-212 Cap is a pipe portal assembly that pairs a laminated, acrylic-coated ABS curb cover with an EPDM C-212 cap. The cover features an 8″ collared opening with a molded sealing ring to seat the cap. The C-212 cap includes stainless-steel Snaplock clamps for a mechanical seal to the collar. This configuration is used where multiple small pipes are routed through a single roof penetration location. Key features: Laminated, acrylic-coated ABS curb cover with...

The Portals Plus 32101 Small RC-2A Straight Sided Roof Curb (11″ High) is designed for decks with lightweight fill or tapered insulation. It is fabricated from 18 gauge galvanized steel with an integral base plate and continuously welded corner seams, includes a factory-installed wood nailer and 1.5″ thick rigid fiberglass insulation (3 lb density) on all four sides. This curb provides a versatile, leak-resistant base for pipe portal systems. Key features: 18 gauge galvanized steel...

The Portals Plus Large Pipe Boot series covers large single-pipe roof penetrations with diameters from 6″ to 12″. These boots feature a compression-molded body (60 mil EPDM or Neoprene) and include the Snaplock stainless-steel clamp to secure the pipe and flashing. Available in black or white EPDM and black neoprene to match roofing membrane finishes and system requirements. Installation should follow Portals Plus instructions and the roofing membrane manufacturer’s guidelines. Key features:...

The Portals Plus 32035 Curb Cover w/ C-481 Cap combines a laminated, acrylic-coated ABS curb cover with an 8″ collared opening and molded sealing ring, paired with the C-481 molded EPDM cap. The cap includes stainless-steel Snaplock clamps to create a mechanical seal to the collar. This assembly is specified for grouped small-diameter penetrations, accommodating up to four pipes from 3/8″ to 1″ in diameter through a single roof portal. Key features: Laminated, acrylic-coated ABS cover with 8″...

The Portals Plus 29225 C-212 Black Cap with Clamps is a molded EPDM compression cap designed to handle up to four roof pipe penetrations—two pipes sized 3/8″ to 1″ diameter and two pipes sized 1″ to 2″ diameter. It includes four stainless-steel adjustable Snaplock clamps to secure the cap around the penetrations. The flexible EPDM cap allows the penetrations to expand, contract, and vibrate independently of the roofing system, and is used in conjunction with a compatible Alumi-Flash or...

The Portals Plus 29245 C-481 Black Cap with Clamps is a molded EPDM compression cap engineered to handle up to four pipe penetrations from .375″ to 1″ in diameter. It comes supplied with four stainless-steel adjustable Snaplock clamps to mechanically secure the cap around the penetrations. The flexible EPDM cap allows penetrations to expand, contract and vibrate independently of the roofing system, and is intended for use on compatible Alumi-Flash or Plasti-Flash base units (base not...

The Portals Plus Small RC-2A Straight-Sided Roof Curb 18″ High (POR-38101) provides a durable mounting base for pipe portal systems on roofs with lightweight fill or tapered insulation. It measures 12″ long by 12″ wide by 18″ high and is constructed from 18-gauge galvanized steel with continuously welded seams for strength and leak prevention. A factory-installed 1.5″ thick 3 lb rigid fiberglass insulation board lines the curb walls, while a wood nailer at the top perimeter ensures secure...

The Portals Plus Deck-Mate Hi-Temp Silicone Flashing is designed to seal pipe penetrations on metal roofs exposed to high-temperature environments. The compression-molded silicone boot offers exceptional heat resistance, flexibility, and weather durability. Its flexible aluminum base conforms to roof profiles for a watertight fit, accommodating pipe diameters from 0.125″ to 26″. With a service range of –100 °F to +500 °F, this flashing delivers long-lasting performance for exhaust, HVAC, and...

The Portals Plus 32025 Curb Cover w/ C-412 Cap Tan is a pre-assembled pipe portal solution designed for roof penetrations. The system comprises a laminated, acrylic-coated ABS plastic curb cover with an 8″ collared opening featuring a molded sealing ring, paired with the C-412 EPDM molded cap and stainless-steel Snaplock clamp. It is specified for roof systems where up to four pipes of 1″-2″ diameter penetrate a single location. Key features: Laminated, acrylic-coated ABS plastic curb cover...

The Portals Plus 22025 Alumi-Flash Standard Base with C-212 Black Cap is a factory-matched flashing system for multiple roof penetrations. The standard base is made from .060" spun aluminum, 4" high, with a 14" base diameter and an 8" collared opening rolled with two beaded sealing rings. The C-212 cap is a molded EPDM component that attaches to the double beads using the stainless-steel Snaplock clamp included with the cap. Together they create a mechanical, weather-tight pressure seal...

The Portals Plus 29215 C-126 Black Cap with Clamp is designed for flashing systems where a single roof penetration sized 2″-6″ in diameter is present. The molded EPDM cap includes the stainless-steel Snaplock clamp for mechanical sealing to the compatible base (Alumi-Flash or Plasti-Flash). The cap allows for independent movement of the penetration relative to the roof membrane, reducing risk of leaks. Key features: Molded EPDM cap model C-126 designed for one penetration sized 2″-6″. ...

Deck-Mate is a molded gray EPDM roof flashing for metal roof and wall systems. Its stepped profile creates a compression seal around Schedule 40 piping, while reinforcing ribs help the boot maintain shape under clamp pressure. A dead soft aluminum flange bends to match roof contours and pitches for a tight fit. The assembly uses a stainless steel clamp to maintain a long-term, watertight seal without relying on caulk. Key features: Stepped EPDM profile forms a compression seal around Schedule...

The Portals Plus Small EPDM Pipe Boots are designed to seal single-pipe roof penetrations on flat roofs. Made from compression-molded EPDM rubber, they provide durable, watertight protection around circular openings. Models 42100 and 42130 include a Snaplock Clamp for mechanical sealing on pipes 1″–3″ in diameter, while model 42500 features an adhesive tape ring for 1.75″–2.75″ pipes. All models come in black EPDM and are packaged 10 per carton. Key features: Durable EPDM body provides...

The Portals Plus 29235 C-412 Black Cap with Clamps is a molded EPDM compression cap designed for flashing roof penetrations between 1″ and 2″ in diameter. It includes stainless-steel adjustable Snaplock clamps that secure the cap to compatible base collars, such as Alumi-Flash or Plasti-Flash units. The flexible EPDM material allows independent movement of the penetration while maintaining a watertight seal, ensuring long-term performance. Key features: Designed for 1″-2″ diameter roof...

The Portals Plus 32005 Curb Cover w/ C-126 Cap is designed for roof penetrations where a single pipe 2″-6″ in diameter passes through the roof. The system includes a laminated, acrylic-coated ABS plastic curb cover with a pre-punched hole and molded sealing ring on an 8″ collared opening, paired with the C-126 EPDM molded cap and stainless-steel Snaplock clamp. Key features: Laminated, acrylic-coated ABS plastic curb cover with pre-punched hole and molded sealing ring. Designed for a single...

The Portals Plus 24025 Alumi-Flash Extra Tall Base with C-212 Black Cap is designed for flashing at locations where up to two pipes .375″-1″ and up to two pipes 1″-2″ in diameter penetrate the roof. The unit includes a .060″ spun aluminum base unit 13″ high with a 14″ base diameter and an 8″ collared opening featuring two roll-formed beaded sealing rings. The molded EPDM cap model C-212 is included with the stainless-steel Snaplock clamp to provide a mechanical weather-tight pressure seal. Key...

The Portals Plus Medium Pipe Boot series provides reliable sealing for single-pipe roof penetrations up to 6″ in diameter. Each boot features a 60 mil compression-molded EPDM or TPO body with a round base that protects against moisture and weather intrusion. All models include a stainless-steel Snaplock Clamp for secure pipe sealing. These boots are available in multiple material and color configurations, making them suitable for EPDM, TPO, or PVC roof systems on flat or low-slope...

The Portals Plus 32041 Large Curb Cover w/ C-182 Cap (Tan) is a complete roof portal assembly designed for large pipe penetrations (8″–12″ diameter). The system features a laminated, acrylic-coated ABS plastic curb cover with a 14″ collared opening and molded sealing ring, paired with an EPDM compression molded cap model C-182 and a stainless-steel Snaplock clamp for a mechanical weather-tight seal. This complete system provides a robust flashing solution for large single-location roof...

The Portals Plus 24045 Alumi-Flash Extra Tall Base with C-481 Black Cap is designed for roof installations where up to four pipes sized .375″ to 1″ diameter penetrate through a single flashing unit. The base is manufactured from .060″ spun aluminum, 13″ in height, with a 14″ base diameter and an 8″ collared opening featuring two roll-formed beaded sealing rings. The molded EPDM cap model C-481 is coupled with a stainless-steel Snaplock clamp to form a mechanical, weather-tight pressure seal...

The Portals Plus 23025 Alumi-Flash Extra Wide Base with C-212 Black Cap is designed for flashing multiple roof penetrations through a single base. The unit features a .060″ spun aluminum base, 4″ high, with an 18″ base diameter and an 8″ collared opening featuring two roll-formed sealing beads. The molded EPDM C-212 cap seats onto the collar beads and uses the stainless-steel Snaplock clamp to establish a mechanical, weather-tight pressure seal. Key features: .060″ spun aluminum base, 4″ high,...

The Portals Plus Double RC-2A Straight-Sided Roof Curb (POR-38161) is engineered for rooftop decking conditions with lightweight fill or tapered insulation where multiple pipe penetrations occur. The specification covers penetrations of up to two pipes 0.375″-1″ in diameter, up to two pipes 1″-2″ in diameter and one pipe 2″-6″ in diameter. The curb shell is fabricated of 18-gauge galvanized steel with integral base plate and continuously welded corner seams, includes a factory-installed wood...

The Portals Plus 22045 Alumi-Flash Standard Base w/ C-481 Black Cap is designed for roof applications where up to four penetrations of .375″ to 1″ diameter pass through a single flashing unit. The system includes a .060-inch spun aluminum base, 4″ high with a 14″ base diameter and an 8″ collared opening featuring two roll-formed sealing beads. The C-481 molded EPDM cap includes the stainless-steel Snaplock clamp and, when seated over the base collar beads, forms a mechanical weather-tight...

The Portals Plus 32055 Curb Cover w/ C-126 White Cap (Tan) is a complete pipe portal solution for a single roof penetration sized 2″-6″ in diameter. The assembly includes a laminated, acrylic-coated ABS plastic curb cover with an 8″ collared opening and molded sealing ring, paired with the C-126 EPDM molded cap and stainless-steel Snaplock clamp. This unit is designed for a clean, finished roof curb penetration detail. Key features: Laminated, acrylic-coated ABS plastic curb cover with...

The Portals Plus 32151 Large RC-4A Raised Canted Curb (9 ½″ High) is designed for insulated deck roof applications. It is constructed of 18-gauge galvanized steel with an integral base plate and continuously welded corner seams. The unit includes a factory-installed wood nailer and 1.5″ thick rigid fiberglass insulation (3-lb density) on all four sides. The raised, canted wall design provides a built-in slope above the deck surface to accommodate insulation loads and ensure a level mounting...

The Portals Plus 32065 Curb Cover w/ C-212 White Cap (Tan) is a pre-assembled pipe portal solution designed for roof penetrations, supporting up to two pipes sized .375″-1″ and two pipes sized 1″-2″. The assembly features a laminated, acrylic-coated ABS plastic cover with an 8″ collared opening and molded sealing ring, paired with the C-212 EPDM cap and stainless-steel Snaplock clamp for mechanical sealing. Key features: Laminated, acrylic-coated ABS plastic curb cover with pre-punched holes...

The Portals Plus Deck-Mate DM#3 Colors w/ Clamps is a molded EPDM flashing boot sized for 1/4″-4″ Schedule 40 pipe penetrations through metal roofs or walls. It features a stepped profile that compresses around the pipe, reinforced ribs for shape stability under clamp pressure, a dead-soft aluminum flange that bends to roof contours, and a stainless steel clamp to maintain a long-term seal without relying on caulk. Key features: Compression seal design using a stepped EPDM profile around...

The Portals Plus Deck-Mate series (models, DM#4, DM#8) consist of color-coded molded EPDM flashing boots designed specifically for metal roof and wall penetrations. Each model features a stepped profile that compresses around the pipe wall, reinforcing ribs for structural stability under clamp load, a dead-soft aluminum flange that conforms to roof contours, and a stainless-steel clamp to maintain a long-term watertight seal. These models support different penetration size ranges and are...

The Portals Plus Double Pipe Portal Cover (POR-36052) provides a weather-tight rooftop penetration solution for a combination of small and medium pipes: up to two pipes sized .375″-1″ and up to six pipes sized 1″-2″ in diameter. It features an 18-gauge galvanized roof curb with welded seams, factory-installed wood nailer and 1.5″-thick 3 lb rigid fiberglass insulation. The cover is made of laminated, acrylic-coated ABS plastic with two 8″ collared openings. Two EPDM compression-molded caps...

The Portals Plus Double Pipe Portal Cover (POR-36142) is designed for roof penetrations where multiple small-diameter pipes (0.375″-1″) must be sealed through one assembly. It includes an 18-gauge galvanized roof curb with integral base plate, continuously welded corner seams, factory-installed wood nailer and 1.5″-thick 3 lb rigid fiberglass insulation. The top cover is laminated, acrylic-coated ABS plastic with two 8″ collared openings and molded sealing rings. Two EPDM compression-molded...

The Portals Plus 29285 SM4 curb cover is a component for pipe portal systems intended for use with C-212, C-412, and C-481 caps. It is made from laminated, acrylic-coated ABS plastic and features a pre-punched hole with a molded sealing ring to seat the compatible cap. This listing is for the cover only; caps are not included. The SM4 configuration provides a clean, finished top for the curb assembly. Key features: Laminated, acrylic-coated ABS plastic construction. Pre-punched hole with...

The Portals Plus 32161 Double RC-2A Straight Sided Curb (11″ High) is designed for dual-pipe portal applications on decks with lightweight fill or tapered insulation. It features an 18-gauge galvanized steel shell with an integral base plate and continuously welded corner seams, a factory-installed wood nailer, and 1.5″ thick rigid fiberglass insulation (3 lb/ft³) on all four sides. This curb is built for dual penetration systems, supporting up to two pipes ⅜″-1″ in diameter, two pipes 1″-2″,...

The Portals Plus 23035 Alumi-Flash Extra Wide Base w/ C-412 Black Cap is designed for flashing roof systems where up to four penetrations of 1″-2″ diameter pass through a single base. The unit includes a .060″ spun aluminum base, 4″ high, with an 18″ base diameter and an 8″ collared opening featuring two roll-formed sealing rings. The molded EPDM C-412 cap is supplied with the stainless-steel Snaplock clamp and the assembly is intended to form a mechanical, weather-tight pressure seal between...

The Portals Plus 22035 Alumi-Flash Standard Base with C-412 Black Cap is intended for flashing roof systems with up to four penetrations sized 1″-2″ diameter. The base construction is .060″ spun aluminum, 4″ high, with a 14″ base diameter and an 8″ collared opening featuring two roll-formed beaded sealing rings. The molded EPDM C-412 cap is designed to mate with the collar beads and includes the stainless-steel Snaplock clamp for a mechanical weather-tight seal. Key features: Supports up to...

The Portals Plus 32111 Small RC-3A Canted Curb (8″ High) is specified for uninsulated decks where a canted (sloped) curb design is required. The unit is fabricated of 18 gauge galvanized steel with an integral base plate, continuously welded corner seams, and a factory-installed wood nailer. It also includes 1.5″ thick, 3 lb density rigid fiberglass insulation on all four sides. This curb is designed to work with Pipe Portal systems and provides a durable mounting solution for roof...

The Portals Plus 24015 Alumi-Flash Extra Tall Base w/ C-126 Black Cap is specified for flashing roof penetrations of 2″-6″ diameter. The system includes a .060″ spun aluminum base unit with height of 13″ and base diameter of 14″. The 8″ collared opening has two roll-formed beaded sealing rings at the top edge. The C-126 molded EPDM cap is used and includes the stainless-steel Snaplock clamp to provide a weather-tight mechanical seal. Key features: Base unit of .060″ spun aluminum with 13″...

The Portals Plus Large RC-2A Straight-Sided Roof Curb 18″ High (POR-38131) is engineered for rooftop applications where major penetrations (8″-12″ diameter) occur through decks with lightweight fill or tapered insulation. The curb box is made from 18-gauge galvanized steel with continuously welded corner seams, includes a wood nailer at the top, and is factory-insulated with 1.5″ thick 3 lb rigid fiberglass. The cover is designed for use with a 14″ collared opening and an EPDM...

Portals Plus Alumi-Flash Standard Base with C-126 Black Cap is a one-penetration flashing for 2″–6″ roof penetrations. The standard base is .060″ spun aluminum, 4″ high, with a 14″ base diameter and an 8″ collared opening rolled with two beaded sealing rings. The C-126 cap is molded EPDM and includes the stainless-steel Snaplock clamp; it mates to the base’s double beads to create a mechanical, weather-tight pressure seal. Key features: Covers a single roof penetration from 2″ to 6″...

The Portals Plus Double Pipe Portal Cover (POR-36042) is designed for roof areas where up to four pipes measuring 0.375″–1″ and up to four pipes measuring 1″–2″ pass through a single curb. It includes an 18-gauge galvanized roof curb with integral base plate, welded seams, factory wood nailer and 1.5″ thick 3 lb rigid fiberglass insulation. The assembly uses a laminated, acrylic-coated ABS plastic curb cover with two 8″ collared openings and molded sealing rings. Two EPDM compression-molded...

The Portals Plus Double Pipe Portal Cover (POR-36032) provides a durable and watertight solution for dual rooftop pipe penetrations. Designed to fit two pipes between 2–6 inches in diameter, it includes an 18-gauge galvanized roof curb with an integral base plate, welded seams, and factory-installed wood nailer. The laminated, acrylic-coated ABS cover features two 8-inch collared openings with molded sealing rings. Each C-126 EPDM compression-molded cap includes a stainless steel Snaplock...

The Portals Plus 23045 Alumi-Flash Extra Wide Base with C-481 Black Cap is designed for flashing roof systems where up to four penetrations of .375″ to 1″ in diameter pass through a single base. The unit includes a .060″ spun aluminum base, 4″ high, with an 18″ base diameter and an 8″ collared opening featuring two roll-formed sealing rings. The molded EPDM C-481 cap is supplied with the stainless-steel Snaplock clamp and the assembly is intended to form a mechanical, weather-tight pressure...

The Portals Plus 29255 C-182 Black Cap w/ Clamp is a molded EPDM compression cap designed for flashing a single roof penetration sized 8″-12″ in diameter. The cap includes a stainless-steel Snaplock clamp and is intended for use in the Portals Plus pipe portal system. Key features: Designed for a single penetration from 8″ to 12″ in diameter.  Includes stainless-steel Snaplock clamp to secure cap to the base collar.  Molded EPDM rubber cap provides robust flashing solution....

The Portals Plus 32181 Double RC-4A Raised Canted Curb is designed for decks with rigid insulation in dual pipe portal applications. The curb is fabricated from 18-gauge galvanized steel, with a full integral base plate, continuously welded corner seams and a factory-installed wood nailer. Insulation is 1.5″ thick, 3-lb density rigid fiberglass on all four sides. The overall size is 27½″ long × 12″ wide × 9½″ high, and the raised canted profile provides a built-in slope for elevated mounting...

The Portals Plus Double Pipe Portal Cover (POR-36092) is engineered for roof installations where multiple medium-sized pipes between 1″ and 2″ in diameter require flashing. It includes an 18-gauge galvanized roof curb with integral base plate, continuously welded corner seams, factory-installed wood nailer, and 1.5″-thick 3 lb rigid fiberglass insulation. The cover is molded ABS plastic with a laminated acrylic coating and includes two 8″ collared openings. Two EPDM compression-molded C-412...

The Portals Plus 24035 Alumi-Flash Extra Tall Base with C-412 Black Cap is engineered for flashing locations where up to four pipes sized 1″-2″ in diameter penetrate the roof. The flashing includes a .060″ spun aluminum base unit with a height of 13″ and a base diameter of 14″. The base features an 8″ collared opening with two roll-formed beaded sealing rings. The molded EPDM cap model C-412 is supplied and includes the stainless-steel Snaplock clamp, forming a mechanical, weather-tight...

The Portals Plus 23015 Extra Wide Alumi-Flash is designed for flashing at points where a single 2″-6″ diameter penetration passes through the roof. It includes a .060″ spun aluminum base, 4″ height, with an 18″ base diameter and an 8″ collared opening featuring two roll-formed beaded sealing rings. The system uses a molded EPDM compression cap model C-126 and includes a stainless-steel Snaplock clamp. (Source: product page) Key features: .060″ spun aluminum base unit with 4″ height and 18″...

The Portals Plus 32171 Double RC-3A Canted Curb is designed for non-insulated decks and used with double pipe portal systems. The curb is fabricated from 18-gauge galvanized steel with an integral base plate and continuously welded corner seams. A factory-installed wood nailer is provided, and 1.5″ rigid fiberglass insulation (3-lb density) lines all four sides. Dimensions are 27½″ in length, 12″ in width, and 8″ in height, suited for dual portal configurations from the same location. Key...