Super Anchor Safety 4034-30SG - Deluxe 12-Strand 30' Lifeline w/ Snaphook 4015 SuperGrab

Our Deluxe Lifeline is made from 12 strand polyolefin cord that is rated for 11,600 pounds. The braided design does not twist or bind making for an easy-to-use, long lasting lifeline. We use an aluminum swage at the anchor end of the lifeline that is rated for over 5,000 pounds. Each lifeline has its own label package and serial number. Numerous lengths and options available.

Features

• Rated for 11,600 lbs.
• Works with all Super Anchor Rope Grabs
• 12 Strand Design for Long Life Cycle
• Resists UV and Water Absorption
• Compatible with all Super Anchor Safety Equipment

• Device: 30 ft vertical lifeline kit with mechanical rope grab and locking snaphook (single-user)
• Rope construction: 12-strand polyolefin copolymer
• Diameter: 5/8 in (≈16 mm)
• Length: 30 ft (9.1 m)
• Minimum tensile strength (rope): 11,600 lb
• Elongation: ~4% at 8 kN
• Termination: aluminum swage (≥5,000 lb) with ANSI-compliant locking snaphook
• Rope grab: 4015 SuperGrab mechanical dual-cam with integral energy absorber (typical MAF ≈900 lb)
• User capacity: 1 person up to 340 lb including tools and equipment
• Anchor requirement: connect only to a 5,000 lb rated anchorage; position above the work area to minimize swing-fall
• Compatible harness: rear D-ring full-body harness (ANSI-compliant)
• Typical service temp: −30 °F to 120 °F
• Weight (assembly): approximately 4.5–6.0 lb (rope, snaphook, SuperGrab, tags)
• Compliance (when used as part of a complete PFAS): OSHA 1926.502; ANSI Z359.1
• Inspection/retirement: inspect before each use; remove from service after any fall event or if cuts, glazing, chemical/UV damage, seized cams, corrosion, or illegible labels are observed

• Q: What’s included in the 4034-30SG kit and what rope does the SuperGrab fit?
  A: You get a 30 ft × 5/8 in 12-strand vertical lifeline with locking snaphook and the 4015 SuperGrab mechanical rope grab with an integral energy absorber. The SuperGrab is designed specifically for 5/8 in 12-strand lifelines—don’t use it on other diameters or rope constructions (e.g., double-braid, kernmantle).
• Q: How should I rig and use the SuperGrab on the lifeline?
  A: Attach the lifeline to a 5,000 lb-rated anchorage positioned above the work area. Install the SuperGrab in the correct orientation (anchor end “up”), connect it to your harness rear D-ring, and slide it upward as you climb; it follows you and locks during a fall. Keep the running end free of knots/debris, maintain the required tail below the grab, and never bypass or remove the integral energy absorber.
• Q: Can more than one person use this lifeline at the same time?
  A: No. It’s a single-user system with a maximum worker capacity of 340 lb including tools and equipment. Do not share the lifeline or anchor with another user unless a qualified person has engineered a multi-user system. Always verify fall clearance and align the lifeline with the expected fall path to reduce swing-fall.
• Q: What inspection and retirement rules apply to the rope and the SuperGrab?
  A: Inspect before each use and periodically by a competent person. Remove from service after any fall event or if you see cuts, glazing, heavy abrasion, chemical/UV damage, damaged stitching or swage, corrosion/deformation, seized cams, or illegible labels. Clean with mild soap and water, air-dry away from heat, and store the kit clean and dry.