ChemLink

Pro Pack is a two-component, RTV, urethane pourable sealant. It is designed for use to fill warranted ChemCurb penetration seals & pitch pans on low-slope roofing systems. It can also be used in horizontal self-leveling, sealing and waterproofing applications. When properly mixed, Pro Pack cures to a tough rubber mass with excellent low temperature elasticity and adhesion. Pro Pack resists deterioration caused by weather, water and ice. It is also resistant to oils, fuels, and many chemicals....

DuraSil is a highly flexible silicone adhesive/sealant/caulk designed for 50% joint movement that can handle very low to high temperature extremes. It bonds to difficult surfaces quickly. Use on glass, aluminum, steel, masonry, polycarbonate, vinyl (PVC), fiberglass (FRP), acrylic, Kynar 500 PVDF, Tedlar PVF, coated metals and concrete. We stock DuraSil in white and translucent. This product contains no biocides or fungicides. It is ultra-low odor when wet and no odor once cured. The white...

F1263 ChemLink DuraLink 35 Multi-Purpose Sealant White 10.1oz Cartridge. ChemLink DuraLink 35 is a multi-purpose, moisture cure, elastomeric sealant that combines economy and high performance. DuraLink 35 has excellent elastomeric properties which is ideal for a wide range of applications including difficult surfaces such as Kynar 500%u00AE PVDF and other anodized metals and coatings. DuraLink 35 is isocyanate free, paintable and SWRI validated for %u00B1 35% joint movement.Bonds to Kynar...

A solvent based liquid primer that is designed to comply with VOC regulations. It can be brush applied to EPDM or TPO roofing membranes, plastics, and any other difficult bonding surface. Installation Read SDS before use. Eliminate all ignition sources. DO NOT SMOKE. Mixing is not recommended, even when settling occurs. Do not thin. Thinning will affect performance. Clean debris from EPDM or TPO surface and wash with isopropyl alcohol. Brush apply the primer directly to the roof surface,...

E-Curbs seal penetrations by using a plastic mold and a pour-in-place polymer seal. E-Curbs are designed for use on granulated modified bitumen, asphalt and coal tar B.U.R. (built up roofing), and are specified for PVC, PIB, and TPO single-ply roofing membranes. The service temperature range for the E-Curbs is -40 F to 200 F, but should not be applied at temperatures below 32 F. This rectangular E-Curb was specifically designed to work with SnapNrack one-hole standoff kits and the SnapNrack HD...

Dangerous snow slides can occur when ice and snow build up on pitched roofs. Help reduce the possibility of personal injury or property damage by installing SNOWSHOES on sloped roof areas SnowShoes are molded from a tough polycarbonate polymer that can withstand heavy impacts at low temperatures. Effective on all metals, including Kynar 500® PVDF coated metal and copper. Also for use on slate, tile, EPDM rubber and PVC and TPO membranes. TPO primer is required with TPO membrane installation....

Green Roofing Solutions by Chem Link ChemCurbs Replaces the old style metal pitch pans with versatile precast curb components, pourable sealant, and structural adhesive/sealant. The system can usually be installed in 15 min. and eliminates the need for flashing or mechanical attachment When installed properly, the ChemCurb system forms a durable waterproof rubber seal around penetrations of any size. An extended warranty against leaks is activated when chemlink products, LLC receives a...

Green Roofing Solutions by Chem Link ChemCurbs replaces the old style metal pitch pans with versatile precast curb components, pourable sealant, and structural adhesive/sealant. The system can usually be installed in 15 min. and eliminates the need for flashing or mechanical attachment When installed properly, the ChemCurb system forms a durable waterproof rubber seal around penetrations of any size. An extended warranty against leaks is activated when chemlink products, LLC receives a...

ChemCurb precast form components are composed of gray polyester resin. The ChemCurb is 2-inches high and is available in a variety of shapes and sizes. Bisected circular curbs have an inside diameter of 7.5 or 5 inches. Straight pieces are available in 6 and 12 inch lengths and combined with 2-inch radius corners to create larger sizes. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light, and ponding water. (Contains 6 curbs per carton only, no adhesive) ...

ChemCurb precast form components are composed of gray polyester resin. The ChemCurb is 2-inches high and is available in a variety of shapes and sizes. Bisected circular curbs have an inside diameter of 7.5 or 5 inches. Straight pieces are available in 6 and 12 inch lengths and combined with 2-inch radius corners to create larger sizes. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light, and ponding water. (Contains 4 curbs per carton only, no adhesive) ...

ChemCurb precast form components are composed of gray polyester resin. The ChemCurb is 2-inches high and is available in a variety of shapes and sizes. Bisected circular curbs have an inside diameter of 7.5 or 5 inches. Straight pieces are available in 6 and 12 inch lengths and combined with 2-inch radius corners to create larger sizes. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light, and ponding water. (Contains 8 straights only, no adhesive) PRODUCT FEATURES RAPID...

ChemCurb precast form components are composed of gray polyester resin. The ChemCurb is 2-inches high and is available in a variety of shapes and sizes. Bisected circular curbs have an inside diameter of 7.5 or 5 inches. Straight pieces are available in 6 and 12 inch lengths and combined with 2-inch radius corners to create larger sizes. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light, and ponding water. (Contains 8 straights only, no adhesive) PRODUCT FEATURES RAPID...

ChemCurb precast form components are composed of gray polyester resin. The ChemCurb is 2-inches high and is available in a variety of shapes and sizes. Bisected circular curbs have an inside diameter of 7.5 or 5 inches. Straight pieces are available in 6 and 12 inch lengths and combined with 2-inch radius corners to create larger sizes. The outer surface is impervious to ice, corrosion, UV (ultraviolet) light, and ponding water. (Contains 8 corners only, no adhesive) PRODUCT FEATURES RAPID...

M-1 is a moisture curing, polyether adhesive/sealant designed for application in damp, dry, or cold climates. M-1 is solvent free and contains no isocyanates. M-1 will not shrink upon curing, will not discolor when exposed to UV light, and can not "out-gas", or bubble, on damp surfaces as urethane sealants often do. M-1 has resilient "elastomeric" properties and excellent adhesion to most construction materials. M-1 is capable of joint movement in excess of 25% in both compression and...

Green Roofing Solutions by Chem Link The MiniCurb™ was designed to seal small penetrations such as HVAC conduit and drains, exterior lighting supports, surveillance cameras, mounts for solar panels and light angle-iron struts. The MiniCurb is built with a special fiberglass reinforced nylon that is tough and durable. Its unique slip-fit components permit quick assembly around penetrations that can't be disturbed. MiniCurbs are installed with the same adhesive as the larger ChemCurbs® and a...

Duralink is an extremely elastic moisture curing sealant designed for use on metal substrates, curtain wall constructions and joints subject to very high movement. Duralink has +/-50% joint movement. Duralink is thermosetting and adheres tenaciously to metal surfaces, most engineering plastics and difficult to bond painted substrates.  Advantages 100% VOC compliant Bonds to PVDF coated metalSolvent Free100% Solids, will not shrinkNon-Slump, applies vertically and overhead30 minute...

Green Roofing Solutions by Chem Link The MiniCurb™ was designed to seal small penetrations such as HVAC conduit and drains, exterior lighting supports, surveillance cameras, mounts for solar panels and light angle-iron struts. The MiniCurb is built with a special fiberglass reinforced nylon that is tough and durable. Its unique slip-fit components permit quick assembly around penetrations that can't be disturbed. MiniCurbs are installed with the same adhesive as the larger ChemCurbs® and a...

Green Roofing Solutions by Chem Link The MiniCurb™ was designed to seal small penetrations such as HVAC conduit and drains, exterior lighting supports, surveillance cameras, mounts for solar panels and light angle-iron struts. The MiniCurb is built with a special fiberglass reinforced nylon that is tough and durable. Its unique slip-fit components permit quick assembly around penetrations that can't be disturbed. MiniCurbs are installed with the same adhesive as the larger ChemCurbs® and a...

1-Part is a moisture curing, pourable sealant designed for use in pitch pans and warranted chem curb penetrations seal, suitable in damp, dry, or cold climates. Part-1 is solvent free, contains no Isocyanates and will not shrink upon curing. Can not " out gas" or bubble on damp surfaces as urathane sealants often do. 1-part has resilient "elastomeric" properties and excellent adhesion to most construction materials. It can be used effectively in many difficult construction site conditions and...

1-Part is a moisture curing, pourable sealant designed for use in pitch pans and warranted chem curb penetrations seal, suitable in damp, dry, or cold climates. Part-1 is solvent free, contains no Isocyanates and will not shrink upon curing. Can not " out gas" or bubble on damp surfaces as urathane sealants often do. 1-part has resilient "elastomeric" properties and excellent adhesion to most construction materials. It can be used effectively in many difficult construction site conditions and...

1-Part is a moisture curing, pourable sealant designed for use in pitch pans and warranted chem curb penetrations seal, suitable in damp, dry, or cold climates. Part-1 is solvent free, contains no Isocyanates and will not shrink upon curing. Can not " out gas" or bubble on damp surfaces as urathane sealants often do. 1-part has resilient "elastomeric" properties and excellent adhesion to most construction materials. It can be used effectively in many difficult construction site conditions and...

Clear is a moisture curing, polyether sealant designed for application in damp, dry, or cold climates. Clear is solvent free and contains no isocyanates. Will not shrink upon curing and will not discolor when exposed to UV light, and can not "out-gass" or bubble on damp surfaces as urathane sealants often do. Clear has resilient "elastomeric" properties and excellent adhesion to most construction materials. Clear is capable of joint movement in excess of 25% in both compression and extension....

NovaLink is a moisture curing, polyether, elastomeric joint sealant designed for application in damp, dry or cold climates. NovaLink is solvent free and contains no isocyanates. NovaLink will not shrink upon curing, will not discolor when exposed to UV light, and can not "outgas" or bubble on damp surfaces as urethane sealants often do. NovaLink has excellent adhesion to most construction materials and resilient elastomeric properties. NovaLink is capable of joint movement in excess of 35%...