Super Anchor Safety 3005-C Tie-Off Strap

A tough, jobsite-ready tie-off strap that creates a fast, reliable anchorage anywhere you have a suitable structural member. Wrap it, choke it, and clip in—3005-C is built from heavy-duty webbing with forged hardware to stand up to daily use while staying flexible for quick installs and easy stowage. Ideal for temporary fall arrest or restraint when used as part of a complete personal fall arrest system.

Features

• Quick choker-style installation around beams, posts, or truss chords; cinches snug to stay put
• Heavy-duty, abrasion- and UV-resistant webbing with reinforced, bar-tack stitching for long service life
• Forged hardware with smooth radii for easy clipping using standard locking snap hooks or carabiners
• Single-user anchor strap for fall arrest or restraint when integrated into a compliant PFAS and adequate fall clearance is maintained
• High-visibility webbing with attached ID/inspection label to streamline pre-use checks
• Compact, tangle-resistant form factor—coils neatly into a bucket or tool bag
• Edge-aware guidance: keep off sharp or hot edges or use appropriate edge protection
• Clear limitations: not a lifting or rigging sling; do not tie knots in the webbing
• Inspection and retirement friendly: remove from service after any fall event or if cuts, glazing, heavy abrasion, chemical/UV damage, broken stitches, or hardware deformation/corrosion are found

• Device: tie-off strap (temporary anchorage) for single-user fall protection
• Model: 3005-C Tie-Off Strap
• Length: 48 in (1.22 m) nominal
• Webbing Width: 2.0 in (≈50 mm)
• Materials: heavy-duty polyester webbing (abrasion/UV resistant); forged steel D-ring and pass-through ring, zinc-plated
• Webbing Thickness: ~0.08–0.10 in (nominal)
• Hardware Openings: connection D-ring ~2.0 in inside diameter; pass-through ring sized for clean choke/cinch
• Weight: ~1.1–1.6 lb per strap
• Minimum Tensile Strength: 5,000 lb (strap/hardware system)
• User Capacity: 1 person up to 310 lb including tools/equipment (as part of a compliant PFAS)
• Dimensions (Packed Coil): approx. 6–7 in diameter × ~2 in thick (for storage/kit planning)
• Typical Use: choke around beams, posts, or truss chords; keep off sharp/hot edges or use edge protection
• Temperature Range: about −30 °F to 120 °F (typical jobsite conditions)
• Finish/Color: high-visibility webbing with bar-tack stitching and ID/inspection label
• Compliance: OSHA 1926.502; ANSI Z359.1 / A10.32 (when used within a compliant system)
• Inspection/Retirement: inspect before each use; remove from service after any fall event or if cuts, glazing, heavy abrasion, chemical/UV damage, broken stitches, or hardware deformation/corrosion are observed

• Q: How do I install it on a beam or truss?
  A: Use a choker wrap: pass the strap through the pass-through ring, cinch snug around a sound structural member, then connect your lanyard/SRL to the D-ring.
• Q: What connectors are compatible?
  A: One ANSI-compliant locking snap hook or carabiner to the D-ring only. Do not clip into the webbing or any sewn loop.
• Q: What are the capacity and strength limits?
  A: Single user up to 310 lb including tools and equipment when used as part of a compliant PFAS; the strap/hardware system is rated to a 5,000 lb minimum tensile strength when installed per instructions.
• Q: When should it be removed from service and how do I care for it?
  A: Retire after any fall event or if you see cuts, glazing, heavy abrasion, chemical/UV damage, broken stitches, or corrosion/deformation on hardware. Clean with mild soap and water, air-dry away from heat, and store dry out of sunlight and chemicals.