Portals Plus Adaptors

The Portals Plus 67255 Underdeck Clamping Ring is a cast-aluminum accessory designed to secure a roof drain bowl to the deck structure. By clamping the drain under the deck substrate or membrane flange, it maintains alignment and prevents movement of the drain bowl under load. It is compatible with roof drain systems that require an under-deck clamp and is suitable for both retrofit and new-construction drain assemblies. Key features: Cast-aluminum construction offers durability and corrosion...

The Portals Plus 14310 Square Tube Adapter for 3 × 3 in is designed to seal square steel-tube roof penetrations without disconnecting the penetration. It provides a retrofit flashing solution whereby the adapter fits around the square projection, seats into a compatible boot, and retains joint movement while maintaining a weather-tight seal. The molded EPDM material is resistant to ozone and UV degradation and supports a service range from –60 °F to +270 °F. Key features: Adapts 3 × 3 in...

The Portals Plus Round Adapter for 1 in OD (Item #: POR-14040) is designed to integrate non-standard or irregular roof penetrations of approximately one-inch outer diameter into a compatible retrofit flashing boot. The adapter fits around the projection, seats into an appropriate step of the boot (boot not included), and is secured via a clamp (not included). This solution enables flashing integrity without custom fabrication and ensures a positive, secure seal around unusual roof...

The Portals Plus Round Adapter for 1-1/4 in. OD (Item #: POR-14050) is designed for sealing smaller irregular or non-standard roof penetrations by adapting a 1-1/4″ outside diameter projection into a compatible retrofit flashing boot. The adapter slips around the projection, seats into the appropriate step of the retrofit boot (boot not included) and then the clamp is tightened (clamp not included) to create a secure watertight seal. This method helps avoid custom boot fabrication for odd...

The Portals Plus Round Adapter for 2 in. outer diameter (Item #: POR-14080) is designed for flashing unusual or non-standard roof penetrations by adapting a 2″ OD projection into a retrofit boot. The adapter fits around the penetration and is inserted into the proper step of the retrofit boot (boot not included); final sealing is achieved by tightening a clamp (not included). This product provides a cost-effective way to use existing boot systems rather than fabricating custom flashings. Key...

The Portals Plus Round Adapter for 7/8 in. OD (Item #: POR-13040) is designed for flashing irregular or non-standard roof penetrations by fitting around a 7/8-inch outer diameter projection and seating into a compatible retrofit boot. The adapter is secured by a clamp (not included) to ensure a watertight seal around the penetration. This solution allows use of existing boots rather than custom fabrications. Key features: Designed to accommodate 7/8″ outer diameter penetrations that standard...

Portals Plus 13010 Small Round Adapter is designed for flashing non-standard, small penetrations by adapting a 3/8-inch OD projection to a compatible retrofit boot. It provides a positive, secure flashing method for unusual shapes by fitting around the penetration and seating into the appropriate step of the retrofit boot. Final sealing is achieved by tightening a clamp over the boot and adapter for a snug fit. Key features: Adapts small or unusual 3/8″ OD penetrations to a compatible retrofit...

The Portals Plus Round Adapter for 2 ½″ OD (Item #: POR-14100) is a retrofit component used to adapt round roof penetrations approximately 2.5 inches outer diameter into a compatible retrofit flashing boot. It is installed by fitting around the projection, seating into the correct step of the boot (boot not included), and tightening a clamp (not included) to achieve a watertight seal. This approach lets installers handle non-standard penetrations without full custom boot fabrication. Key...

The Portals Plus Round Adapter for 3 in. OD (Item #: POR-14120) is designed to flash small or non-standard roof penetrations by adapting a 3-inch outer-diameter projection to a compatible retrofit boot. The adapter fits around the penetration, seats into the appropriate step of the retrofit boot, and is then tightened with a clamp (boot and clamp not included). This provides a positive, secure method for flashing irregular shapes. Key features: Adapts 3″ OD penetrations to compatible retrofit...