Van Mark UNL1 UniLeg for TrimMaster Brakes - TM10 & IT10

The Van Mark UNL1 UniLeg is a compact, center support leg designed specifically for TrimMaster TM10 and IT10 brakes. Mounted under the middle of the brake, it helps carry the load of long, heavy pieces of trim coil or metal, reducing flex and improving overall stability. Whether you run your TrimMaster on sawhorses, a platform, or a custom bench, the UniLeg adds that crucial third point of contact, helping keep the brake level and bending more accurate over its full 10' 6" length. Tough, simple, and easy to adjust, it’s a go-to accessory for contractors who want straighter bends and a more solid feel from their brake setup.

Key Features

• Purpose-Built for TM10 & IT10 Brakes
  Designed to work with Van Mark TrimMaster TM10 and Industrial TrimMaster IT10 models, providing proper center support right where the brake needs it most.
• Reduces Flex on Long Bends
  Supports the middle of the brake to help minimize sag and flex when you’re bending full-length fascia, drip edge, and other long trim pieces.
• Improved Stability & Leveling
  Acts as a third support point between your two primary stands or sawhorses, helping keep the brake level and stable for more consistent, repeatable bends.
• Adjustable Height Design
  Height-adjustable leg lets you fine-tune the support to match different platforms, stands, or site conditions so everything lines up correctly.
• Compact & Lightweight
  Small and easy to handle, the UniLeg is simple to carry, position, and store without adding bulky gear to your truck or trailer.
• Rugged Construction
  Built from durable, contractor-grade materials with a protective finish to withstand daily jobsite use, transport, and outdoor conditions.
• Easy to Install & Use
  Straightforward mounting and adjustment mean crews can quickly set it up or move it as needed without special tools or complicated hardware.

Compatibility:

• Designed specifically for Van Mark TrimMaster TM10 and Industrial TrimMaster IT10 brakes
• Provides centered under-brake support for 10' 6" models

Weight:

• Approx. 10–15 lbs (lightweight, easy for one-person handling)

Dimensions (Approximate):

• Height Range: Adjustable to match stands, sawhorses, or custom platforms
• Base Width: Compact footprint for easy positioning under the brake
• Overall Size: Slim, space-saving design intended for mid-span support (exact dimensions vary slightly by production run)

Material:

• Construction: Heavy-duty steel for long-term stability
• Hardware: Steel adjustment components
• Finish: Powder-coated for corrosion and wear resistance

Adjustment Features:

• Height-adjustable to fine-tune brake leveling
• Allows compensation for uneven ground or mismatched support surfaces
• Designed to eliminate mid-span sag during long bends

Support Performance:

• Adds a third point of contact to increase brake rigidity
• Helps maintain consistent bend depth over the full working length
• Reduces flex when bending long fascia, drip edge, and trim profiles

Portability:

• Lightweight, compact, and easy to store
• Quick positioning and removal — ideal for mobile crews

Use Case:

• Provides mid-span support for TrimMaster brakes used on sawhorses, platforms, or stands
• Ideal for siding, roofing, and trim fabrication requiring long, precise bends

Q: What is the Van Mark UNL1 UniLeg used for?
A: The UNL1 UniLeg is a center support leg for Van Mark TrimMaster TM10 and IT10 brakes. It mounts under the middle of the brake to provide extra support, helping reduce flex and improve stability when bending long pieces of metal or trim coil on the jobsite.

Q: Do I still need stands or sawhorses if I use the UniLeg?
A: Yes. The UniLeg is designed to work in addition to your main supports, not replace them. You still use your stands or sawhorses at each end of the brake, and the UniLeg adds a third support point under the center to help keep the brake level and more rigid during long bends.

Q: Can I adjust the height of the Van Mark UNL1 UniLeg?
A: Yes. The UniLeg features an adjustable-height design so you can fine-tune the center support to match different stand heights, sawhorses, or platforms. This helps you level the brake properly and maintain consistent bends across the full 10' 6" working length.

Q: Is the UNL1 UniLeg easy to move and store between jobs?
A: Yes. The UNL1 is compact and relatively lightweight, making it easy for one person to carry, position, and remove. Its small footprint and simple design mean it doesn’t take up much room in your truck, trailer, or shop when not in use.