Best Price Guaranteed
Price: $10.45
    Item #OATEY-11872
    Write a review!
    Quantity:

    Overview

    Oatey® Color-Flash® All-Flash® No-Calk® Roof Flashings feature a color base designed to match roof color in commercial and residential applications that require a watertight seal for roof penetrations around the plumbing vent pipe. Self-sealing collar slides over pipe and requires no caulking. Oatey products have earned the trust of plumbing professionals for over 100 years.

    • 3"-4" Brown Galvanized Roof Flashing
    • 28 gauge 12" x 15" galvanized steel base
    • Color base designed to match roof color
    • For pitch from 0-40°
    • Rated 180°F continuous heat and approved for Type B installations
    • Self-sealing collar slides over pipe and requires no caulking
    • Do not use petroleum based products or paint on flashing collar or plastic base
    • Not for hot-mopped or built-up roofs
    • For warranty product details, refer to the Oatey Limited Warranty document

    How To Use

    Make sure roof is clean and free from any major protrusion.

    Before roof covering is installed:

    • No tar, asphalt-based roof cement or "pitch" should be applied to the collar portion of any metallic
    • No-Calk flashing or the base or collar portion of any Thermoplastic or Flexible No-Calk flashing.
    • At the discretion of the installer, silicone sealant can be applied over all exposed nails or staples.
    • Silicone sealant can also be applied to the underside of the base to increase sealing power to the roof and is recommended in areas where frequent or heavy precipitation is common.

    1. Place correct size No-Calk flashing over vent stack with angle facing down slope of the roof. Push firmly to base

    of stack until flashing lies flat on the roof. Flashing size should be equivalent to pipe diameter size (i.e. 1.5"

    flashing for 1.5" pipe, 2" flashing for 2" pipe size, etc...). The Oatey logo printed on the flashing represents the

    front or down slope side of the flashing.

     2. Using corrosion resistant nails or staples, secure the top of the flashing (the end closes to the crest of the roof) at

    teach corner and along the sides at 4"-6" intervals to secure flashing to the roof. One nail or staple in each bottom

    corner is appropriate. The top of the flashing will be covered one-quarter to one-half of the way down with

    roofing shingles. The bottom edge of the flashing should overlap the shingles beneath it so it shed, not traps,

    water.

    Oatey Thermoplastic base flashings are designed to fit roof angles from flat to 45 degrees. Flexible, Galvanized,

    Aluminum and Copper Base Flashings are designed to fit roof angles from flat to 38 degrees. Oatey All-Flash

    High-Rise Thermoplastic Roof Flashings are designed to fit roof angles from flat to 60 degrees.

    Additional Information

    • Material: Galvanized Steel
    • Product Type: All-Flash No Calk
    • Pipe Diameter: 1.25 in. - 3 in.
    • Weight: .95 lb
    • Base Size/Diameter: 11" X 14.5"

    Reviews (0) • Write a review!

    This product has no reviews yet. Write a review!

    Related Items
    Oatey, #12803 Aurora No-Calk Solar Flashing 1-1/2 in. - 3...
    For applications where a watertight seal for roof penetrations around the piping for solar mounting system is required
    Price: $7.85
    Availability: In Stock
    Usually ships within 1-2 Business Days

      Oatey Aurora No-Calk Solar Flashings can be used in commercial and residential applications where a watertight seal for roof penetrations around the piping for solar mounting system is required. Low profile flashing collar design provides a clean finished appearance. Solar Flashings are available in Soft Aluminum, Aluminum and Galvanized Bases.

      Oatey, #12804 Aurora No-Calk Solar Flashing 1-1/2 in. - 3...
      For applications where a watertight seal for roof penetrations around the piping for solar mounting system is required
      Price: $8.65
      Availability: In Stock
      Usually ships within 1-2 Business Days

        Oatey Aurora No-Calk Solar Flashings can be used in commercial and residential applications where a watertight seal for roof penetrations around the piping for solar mounting system is required. Low profile flashing collar design provides a clean finished appearance. Solar Flashings are available in Soft Aluminum, Aluminum and Galvanized Bases.

        Oatey, #12802 Aurora No-Calk Solar Flashing 1/2 in. -...
        For applications where a watertight seal for roof penetrations around the piping for solar mounting system is required
        Price: $9.15
        Availability: In Stock
        Usually ships within 1-2 Business Days

          Oatey® Aurora™ No-Calk® Solar Flashings are designed for use in commercial and residential applications that require a watertight seal for roof penetrations around the piping for solar mounting systems. Self-sealing collar slides over pipe and requires no caulking. Oatey products have earned the trust of plumbing professionals for over 100 years. 1/2 in. to 1-1/2 in. Galvanized Roof Flashing28 Gauge 9.5 in. x 12.5 in. galvanized steel baseFor pitch from 0-40°Rated 180°F continuous heat and...

          Oatey, #12801 Aurora No-Calk Solar Flashing 1/2 in. -...
          For applications where a watertight seal for roof penetrations around the piping for solar mounting system is required
          Price: $7.95
          Availability: In Stock
          Usually ships within 1-2 Business Days

            Oatey® Aurora™ No-Calk® Solar Flashings are designed for use in commercial and residential applications that require a watertight seal for roof penetrations around the piping for solar mounting systems. Self-sealing collar slides over pipe and requires no caulking. Oatey products have earned the trust of plumbing professionals for over 100 years. 1/2" to 1" Galvanized Roof Flashing28 Gauge 9.5" x 12.5" galvanized steel baseFor pitch from 0-40°Rated 180°F continuous heat and approved for Type B...

            Leave a message