Best Price Guaranteed
Price: $7.05
    Item #OATEY-11830
    Write a review!
    Quantity:

    Overview

    Oatey® Galvanized No-Calk® Solar Flashings are designed for commercial and residential applications that require a watertight seal for roof penetrations around the plumbing vent pipe. Self-sealing collar slides over pipe and requires no caulking. Oatey products have earned the trust of plumbing professionals for over 100 years.

    • 28 gauge Galvanized steel base
    • Collar seals pipe ranging from 1/2 In to 1 In to accomodate solar panel mounting system posts
    • Rated 180°F continuous heat and approved for Type B installations
    • Metal base for pitch from 0-40° or up to 10/12 roof
    • Self-sealing collar slides over pipe and requires no caulking
    • Collar will not fade
    • Do not use petroleum based products or paint on flashing collar or plastic base
    • Not for hot-mopped or built-up roofs

    How To Use

    Make sure roof is clean and free from any major protrusion.

    Before roof covering is installed:

    • No tar, asphalt-based roof cement or "pitch" should be applied to the collar portion of any metallic
    • No-Calk flashing or the base or collar portion of any Thermoplastic or Flexible No-Calk flashing.
    • At the discretion of the installer, silicone sealant can be applied over all exposed nails or staples.
    • Silicone sealant can also be applied to the underside of the base to increase sealing power to the roof and is recommended in areas where frequent or heavy precipitation is common.

    1. Place correct size No-Calk flashing over vent stack with angle facing down slope of the roof. Push firmly to base of stack until flashing lies flat on the roof. Flashing size should be equivalent to pipe diameter size (i.e. 1.5" flashing for 1.5" pipe, 2" flashing for 2" pipe size, etc...). The Oatey logo printed on the flashing represents the front or down slope side of the flashing.
    2. Using corrosion resistant nails or staples, secure the top of the flashing (the end closes to the crest of the roof) at each corner and along the sides at 4"-6" intervals to secure flashing to the roof. One nail or staple in each bottom corner is appropriate. The top of the flashing will be covered one-quarter to one-half of the way down with roofing shingles. The bottom edge of the flashing should overlap the shingles beneath it so it shed, not traps, water.

    Oatey Thermoplastic base flashings are designed to fit roof angles from flat to 45 degrees. Flexible, Galvanized, Aluminum and Copper Base Flashings are designed to fit roof angles from flat to 38 degrees. Oatey All-Flash High -Rise Thermoplastic Roof Flashings are designed to fit roof angles from flat to 60 degrees.

    Specifications

    • Material: Galvanized Steel
    • Brand: Oatey
    • Product Type: No Calk
    • Pipe Diameter: .5"-1"
    • Weight: .7lbs
    • Color: Unfinished
    • Base Size/Diameter: 9 x 12.5"

    Reviews (0) • Write a review!

    This product has no reviews yet. Write a review!

    Related Items
    Oatey, #11871 Galvanized Base Multi-Size Roof Flashing...
    Shingle Flashings are designed to effectively seal round pipe penetrations, seals different pipe diameters.
    Price: $7.95
    Availability: In Stock
    Usually ships within 1-2 Business Days

      Reduces inventory: 2 multi-size flashings fit 4 pipe sizes. One flashing accommodates 1-1/2", 2", and 3" pipes; the other, 3" and 4" pipes. Ring on collar tears off, allowing flashings to seal different pipe diameters. Simply remove the inner ring at the indicated point on the collar and you'll have a perfect leakproof fit for pipes from 1-1/2" to 4". Slides over pipe - for pitch to 40 degrees. Rustproof, stamped galvanized, 24 or 28 gauge. Non-fading, non-cracking and non-rusting bases and...

      Oatey, #12802 Aurora No-Calk Solar Flashing 1/2 in. -...
      For applications where a watertight seal for roof penetrations around the piping for solar mounting system is required
      Price: $9.15
      Availability: In Stock
      Usually ships within 1-2 Business Days

        Oatey® Aurora™ No-Calk® Solar Flashings are designed for use in commercial and residential applications that require a watertight seal for roof penetrations around the piping for solar mounting systems. Self-sealing collar slides over pipe and requires no caulking. Oatey products have earned the trust of plumbing professionals for over 100 years. 1/2 in. to 1-1/2 in. Galvanized Roof Flashing28 Gauge 9.5 in. x 12.5 in. galvanized steel baseFor pitch from 0-40°Rated 180°F continuous heat and...

        Oatey, #12803 Aurora No-Calk Solar Flashing 1-1/2 in. - 3...
        For applications where a watertight seal for roof penetrations around the piping for solar mounting system is required
        Price: $7.85
        Availability: In Stock
        Usually ships within 1-2 Business Days

          Oatey Aurora No-Calk Solar Flashings can be used in commercial and residential applications where a watertight seal for roof penetrations around the piping for solar mounting system is required. Low profile flashing collar design provides a clean finished appearance. Solar Flashings are available in Soft Aluminum, Aluminum and Galvanized Bases.

          Oatey, #11877 Galvanized Base Multi-Size Roof Flashing 3-4...
          Shingle Flashings are designed to effectively seal round pipe penetrations, seals different pipe diameters.
          Price: $8.35
          Availability: In Stock
          Usually ships within 1-2 Business Days

            Oatey® All-Flash® No-Calk® Roof Flashings can be used in commercial and residential applications where a watertight seal for roof penetrations around the plumbing vent pipe is required. The patented collar design allows for use on multiple pipe sizes. Oatey products have earned the trust of plumbing professionals for over 100 years. 3 in.–4 in. 28-gauge galvanized steel roof flashing12 in. x 15 in. basePatented All-Flash® collar with tear-away ring for many pipe sizesSelf-sealing collar slides...

            Leave a message