Price: $134.65
Item #E-OPG-1C
Write a review!
Description
EternaBond EternaPrime is a solvent-based surface conditioner formulated for use when surfaces are oxidized, dirty, or difficult to clean, or when installation temperatures are below 40°F. It coalesces loose particles into a solid surface ready for tape adhesion and enhances bond performance under cold or dusty conditions. This primer is VOC-exempt in its brush-on version and compatible with most EternaBond tapes.
Key features:
-
Designed for use on dirty, oxidized, or porous surfaces
-
Allows tape installation in temperatures below 40°F
-
Improves adhesion of EternaBond tapes on rough substrates
-
Solvent-based formulation with elastomer and resin blend
-
VOC-exempt and compatible with brush or roller application
Specifications
- Container size: 1 gallon
-
Standard case quantity: 1 gallon per case
-
Application temperature range: -20°F to 205°F
-
Film thickness (wet): approximately 4 mils
-
Drying time at 60°F: about 15 minutes
-
Coverage: over 300 square feet per gallon
-
Flash point: 110°F
-
Viscosity: 135–152 cps
-
Weight: approximately 10 lbs per gallon
-
Storage: store in original sealed container away from heat, flame, and oxidizers
* This item is hazmat *
How To
- Clean the surface thoroughly, removing loose dust, rust, scale, talc, and debris.
-
Remove oil or grease using a suitable solvent-based cleaner.
-
Stir the EternaPrime thoroughly and apply evenly using a brush or roller.
-
Allow the primer film to set for approximately 15 minutes at 60°F before applying EternaBond tape.
-
Proceed with EternaBond tape application once the surface is fully primed and dry.
FAQs
Q: When should EternaPrime be used?
A: EternaPrime should be used when bonding surfaces that are dirty, oxidized, porous, or when installation temperatures are below 40°F.
Q: Can EternaPrime be applied to PVC roofing materials?
A: No, EternaPrime should not be used on PVC roofs due to potential plasticizer reactivation.
Q: How long should EternaPrime dry before applying EternaBond tape?
A: The primer typically sets in about 15 minutes at 60°F before the tape should be applied.
Q: What sizes are available for EternaPrime?
A: EternaPrime is available in 12.2 oz spray, quart, and gallon containers.
Reviews (0) • Write a review!
This product has no reviews yet. Write a review!
Eternabond - OPQ-1C EternaPrime , Quart
Use EternaPrime when surfaces to be bonded are very dirty or temperature is below 40 degrees F.
Price: $39.95
Availability: Discontinued
EternaPrime is used when surfaces to be bonded are very dirty, oxidized, dusty, or when installation temperature will be below 40 °F. It coalesces loose particles into a solid platform for adhesion of EternaBond tapes. The brush-on version is VOC exempt. Key features: Prepares surfaces that cannot be fully cleaned (rust, scale, dust, tar/gravel) for tape adhesion Enables tape installation in lower ambient temperatures (below 40 °F) Solvent-based primer with elastomer/resin blend and VOC exempt...
Eternabond - OPS1-C EternaPrime , 12.2 oz. Spray
Use EternaPrime when surfaces to be bonded are very dirty or temperature is below 40 degrees F.
Price: $27.20
Availability: Discontinued
EternaBond EternaPrime is used to condition surfaces that are oxidized, dusty, or cannot be fully cleaned, or when installation temperatures drop below 40 °F. It helps coalesce loose particles into a solid surface suitable for tape adhesion and is VOC-exempt in its brush-on version. (based on Big Rock Supply description) Key features: Prepares dirty, oxidized or dusty surfaces for tape adhesion Enables installation of EternaBond tapes at temperatures down to approximately -20 °F (with proper...