Snow Retention

The S-5! VersaGard is a multifunctional bracket engineered for use on exposed-fastened metal roof panels. It is commonly used as part of the VersaGard snow guard system, securing pipes that act as snow retention barriers to reduce rooftop avalanches. Additionally, VersaGard can be used as a utility mounting bracket for a wide variety of rooftop applications. Its factory-applied EPDM sealing washers ensure watertight installation without additional sealants. Made from high-strength cast...

The American made SnoBlox Deuce has revolutionized the polycarbonate snow guard industry with its low profile forward mounted 2.5" high face and its sleek 1.5" wide waffled tapered back base that fits most roof panels without rib straddling. This patented product has stood the test of time and is an aesthetically appealing, low cost solution to the problem of sliding snow and ice on metal roofing. It's mounting versatility allows it to be mechanically attached on screw down roofs with a 1.5"...

ChemLink SnowShoe Snow Guards are an adhesive-applied snow retention accessory used to help reduce sudden snow and ice slides off pitched roofs. They’re molded from a durable polycarbonate polymer and are used on a wide range of roof surfaces, including metal, slate, tile, and single-ply membranes. Each carton includes 24 snow guards and the adhesive needed for installation. SnowShoe guards are available in multiple color options for a cleaner finished look on the roof. Key Features...

SureBond SB-190 is the official snow guard adhesive of SnoBlox-Snojax. We pioneered the use of this adhesive with our polycarbonate snow guards over 25 years ago and now it has become the standard in the industry. For a successful installation the adhesive requires 28 days or (672 Hours) at 50 Degrees (F) or above to achieve full cure. Temperatures below 40 Degrees (F) will delay cure time, until temperatures reach 50 Degrees (F) or above to completely cure. Spring, Summer or early Fall is the...

The S-5! A-SF Aluminum SnoRail/SnoFence Clamp is engineered for use with the SnoRail and SnoFence snow retention systems on standing seam metal roofs. Constructed of high-quality aluminum, it accommodates both vertical and horizontal seam orientations by rotating the clamp 90°, and is built for seams with finished thickness up to 0.40″. The clamp uses patented round-point stainless steel setscrews designed to dimple, not pierce, the roof panels—maintaining the coating and allowing thermal...

The S-5! AE Aluminum End Clamp is a dedicated component of the SnoRail and SnoFence snow retention systems. It is designed to be installed at the ends of SnoRod runs and at intermediate fixed positions to prevent the rods from migrating laterally. Unlike standard intermediate clamps, the AE End Clamp fixes the rod firmly in place, while other clamps allow thermal expansion and contraction. Constructed of durable aluminum with stainless steel hardware, it ensures secure anchoring and long...

DualGard is a robust two-pipe snow guard system by S-5! designed for use on standing seam and corrugated metal roofs. It uses 1-inch diameter aluminum crossmembers (DualPipe) mounted via DualBrackets and S-5! Mini clamps or CorruBracket attachments. Optional DualClip components may be added under certain conditions to retard snow/ice migration under the bars. The system includes splices, collars, and endcaps for continuous pipe runs. It can be powder-coated or anodized to match roof finishes....

The S-5! DualPipe is the aluminum crosspipe component used in DualGard and VersaGard snow retention systems. It features a 1-inch diameter with a 1/8-inch wall for structural strength, and is engineered to integrate seamlessly with S-5! brackets, clamps, and hardware to create a durable, two-pipe snow guard assembly for metal roofs. Key Features: • 1" diameter aluminum pipe with 1/8" wall thickness • Supplied in 7' 8" (DualGard) or 8' (VersaGard) lengths • Engineered for use with S-5! DualGard...

The S-5! NEX 2.0 Pipe is the primary horizontal crosspipe for X-Gard snow retention systems. Engineered from aluminum for strength and durability, it integrates with S-5! X-Gard clamps and brackets to provide high-performance snow management for standing seam and other compatible metal roof profiles. Key Features: • Core structural pipe component for X-Gard snow retention systems • Engineered aluminum pipe ensures strength and durability • Works with S-5! X-Gard clamps, brackets, and...

The S-5! DualCollars & Endcaps kit is an accessory for the DualGard snow retention pipe system. The kit contains four DualCollars to lock DualPipe in place at assembly ends, and four Endcaps sized to fit snugly into DualGard Pipes to seal pipe ends against rain, dirt, and debris. Made of stainless steel, this 4-piece set ensures clean finished ends and prevents lateral movement of the pipe. Other DualGard components (DualPipe, brackets, clamps) are required separately.Key Features: Includes...

The S-5! SnoPost is a stainless steel accessory used in the SnoFence snow retention system. When threaded into the matching S-5 clamp (typically ASF for aluminum/stainless or BSF for brass systems), it provides attachment for a second rod (SnoRod) positioned approximately 2 inches above the first rod. This two-rail design improves snow retention performance under heavier service loads. The SnoPost helps prevent snow sliding by increasing resistance, especially when long rods span between...

The S-5! X-Gard 1.0 Bracket is a heavy-duty snow retention system component designed to hold one NEX 2.0 pipe firmly across standing seam metal roofs. Built from high-strength aluminum with stainless steel hardware, the bracket attaches securely to S-5! clamps, ensuring long-term reliability without compromising roof integrity. This bracket is engineered for use in regions with heavy snow loads, helping prevent snow avalanches that could damage property or endanger pedestrians. When combined...

The S-5! Endcap for X-Gard is a simple but essential accessory for the X-Gard snow retention system. It caps the open ends of NEX 2.0 pipes to prevent entry of water, debris, insects, and vermin, which could compromise system integrity or lead to corrosion and damage inside the pipe. Made of durable black vinyl, the endcap stretches to fit snugly and remains flexible over time, even under temperature extremes. It is used at every open pipe end in the snow guard assembly and helps ensure the...

The S-5! DualClips are optional accessory clips for the DualGard Snow Retention System. They attach to the DualPipe crossmembers to help prevent snow and ice from migrating under the snow guard pipes. There are two sizes: DualClip II for smaller seam heights and DualClip III for taller seams. Both use a rubber foot for panel protection. Key Features: • Two sizes available: DualClip II and DualClip III • Aluminum body with soft rubber foot to protect roof panel finish • Prevent ice & snow...

The S-5! FA (Flange Adapter) is an accessory that converts an existing S-5! mini clamp into a flanged clamp. It attaches with an M8 bolt to most mini clamps and provides a slotted flange for mounting utilities, rails, or other attachments. The flange is curved for structural stiffness, allowing attachment at various angles around the clamp. Hardware such as flange nuts or bolts for utility mounting are sold separately.Key Features: Adapts virtually any S-5! mini clamp (except brass) into a...

#14 Wood Purlin Snow Guard Screws These are #14, self-tapping snow guard screw that is 2 inches long with an attached neoprene washer. They are made from case hardened carbon steel construction with an anti-corrosion protective coating. They measure 1/4 - 14 X 2" Teks/3 screws feature a pre-threaded bonded washer and a 3/8” high hex washer head. This screw is design for snow guard attachment into wood purlins or wood substrates at least 2" thick. #14 Metal Purline Snow Guard Screws These are...

The S-5! X-Clip II is an optional accessory designed for the S-5! X-Gard 1.0 and 2.0 snow retention systems. This clip mounts to the NEX 2.0 pipe and rests on the roof panel flat, using its integrated rubber foot to reduce snow and ice migration under the rail. It is engineered for seam heights between 1″ and 1.75″, with added compatibility for some 2″ vertical seams. Made from durable aluminum with a protective rubber foot, the X-Clip II installs easily and includes a stainless steel...

The S-5! X-Clip III is an optional component for the X-Gard 1.0 and 2.0 snow retention systems. It mounts to the back of the NEX 2.0 pipe and its rubber foot rests on the flat of the roof panel. Designed for seam heights between 2″ and 3″, it helps prevent snow or ice from slipping beneath the rail while protecting panel finish.Key Features: • Aluminum body with integrated rubber foot for panel protection • Compatible with X-Gard 1.0 and 2.0 systems • Fits seam heights 2″ to 3″ (51 mm to 76...